The Elsmar Cove Wiki More Free Files The Elsmar Cove Forums Discussion Thread Index Post Attachments Listing Failure Modes Services and Solutions to Problems Elsmar cove Forums Main Page Elsmar Cove Home Page

Go Back   The Elsmar Cove Forum > Common Quality Assurance Processes and Tools > Nonconformance and Corrective Action
Forum Username


Elsmar Cove Forum Sidebar
Custom Search
Monitor the Elsmar Forum
Monitor New Forum Posts
Follow Marc & Elsmar
Elsmar Cove Forum RSS Feed  Marc Smith's Google+ Page  Marc Smith's Linked In Page   Marc Smith's Elsmar Cove YouTube Page  Marc Smith's Facebook Page
Elsmar Cove Groups
Elsmar Cove Google+ Group  Elsmar Cove LinkedIn Group  Elsmar Cove Facebook Group
Sponsor Links







Donate and $ Contributor Forum Access
Sponsored Links
Courtesy Quick Links

Links that Elsmar Cove visitors will find useful in your quest for knowledge:


Howard's
International Quality Services

Atul's
Symphony Technologies

Marcelo Antunes'
SQR Consulting

Bob Doering's
Correct SPC - Precision Machining


NIST's Engineering Statistics Handbook

IRCA - International Register of Certified Auditors

SAE - Society of Automotive Engineers

Quality Digest Portal

IEST - Institute of Environmental Sciences and Technology

ASQ - American Society for Quality

Reply
 
Thread Tools Search this Thread Rate Thread Content Display Modes
  #1  
Old 19th April 2001, 04:12 PM
energy
Unregistered Guest

 
 
Posts: n/a
Thumbs down Rejection Tags

This is probably my most important post since my first visit to the "Cove". Can anybody tell me where I can purchase a two part rejection tag. You know, one that you tear of the first part and leave the red rejection tag attached to the component. I've located only one through research and there are boxes on it that we will never utilize. All I need is the manufacturer/distributor of the tag to compare format. One thing I do know for sure. Most people who visit this site own a "Red Rejection Tag". If you choose not to clutter up the site, e-mail directly to me. Thank you in advance,
energy

Sponsored Links
  #2  
Old 19th April 2001, 05:14 PM
DICKIE
Unregistered Guest

 
 
Posts: n/a
Energy,
We used a local printer to print out custom tags with the fields that we needed. They can also print on carbon type tearaways. I'm sure any printer in your area can do the same thing. Most have "art" departments to do the design or they can print right from your scale design

Greg
Sponsored Links

  #3  
Old 19th April 2001, 05:53 PM
freeda
Unregistered Guest

 
 
Posts: n/a
Same here.
We send them a sample of what we want and they make them.
  #4  
Old 20th April 2001, 09:13 AM
energy
Unregistered Guest

 
 
Posts: n/a
My boss is cheap. Does anybody use a two part tag that is purchased as is? We will address the information areas in our procedure. Anybody? I can buy 1000 for $140, with $15 for 1000 wires. Just don't like the boxes and the signatures that are required. Engineering, Production, etc.
  #5  
Old 20th April 2001, 09:53 AM
Jim Evans
Unregistered Guest

 
 
Posts: n/a
Try Elite Graphics out of Warren, Michigan. They have some "as is" tags. I beleive they will do custom work too. I think they will send you a sample package of all sorts of tags, stickers etc. upon request. Their phone number is 810-755-9236.

By the way if you don't like using certain portions of a particular tag, write your procedure/work instruction to reflect that portion of the tag is not required to be filled out.

Best Regards,

Jim Evans

[This message has been edited by Jim Evans (edited 20 April 2001).]
  #6  
Old 21st April 2001, 01:34 AM
Sam's Avatar
Sam Sam is offline

 
Registration Date: Sep 1999
Location: Oklahoma
Age: 71
 
Posts: 1,447
Thanks Given to Others: 1
Thanked 48 Times in 27 Posts
Karma Power: 202
Karma: 1115
Sam is appreciated, and has over 1100 Karma points.Sam is appreciated, and has over 1100 Karma points.Sam is appreciated, and has over 1100 Karma points.Sam is appreciated, and has over 1100 Karma points.Sam is appreciated, and has over 1100 Karma points.Sam is appreciated, and has over 1100 Karma points.Sam is appreciated, and has over 1100 Karma points.Sam is appreciated, and has over 1100 Karma points.Sam is appreciated, and has over 1100 Karma points.
Energy, We are cheaper then that. We just attach a copy of the nonconforming report to the container. If a nonconforming report was not necessary, then we just apply a length of red Tape. (No pun intended)
  #7  
Old 5th August 2005, 09:31 AM
Riverside Riverside is offline
Inactive Registered Visitor

 
Registration Date: Aug 2005
Location: US / PA.
 
Posts: 3
Thanks Given to Others: 0
Thanked 0 Times in 0 Posts
Karma Power: 32
Karma: 10
Riverside has less than 100 Karma points so far.
I have recently purchased some tags from Kenmore Tags. Their web page is
www.kenmorelabel.com they have two part tags.
Reply

Lower Navigation Bar
Go Back   The Elsmar Cove Forum > Common Quality Assurance Processes and Tools > Nonconformance and Corrective Action

Do you find this discussion thread helpful and informational?


Bookmarks


Visitors Currently Viewing this Thread: 1 (0 Registered Visitors (Members) and 1 Unregistered Guest Visitors)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Forum Search
Display Modes Rate Thread Content
Rate Thread Content:

Forum Posting Settings
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Discussion Threads
Discussion Thread Title Thread Starter Forum Replies Last Post or Poll Vote
Customer rejection because he "doesn't like it." - No specific rejection criteria J Allen Inspection, Prints (Drawings), Testing, Sampling and Related Topics 14 22nd July 2009 11:47 PM
Tags - Thread 'Tags' - New in vBulletin version 3.7 Marc Forum Software - How to Do Things in the Elsmar Forum --> Instructions 15 20th May 2009 04:49 PM
Calibration Tags - External company applied their tags - Do I need to apply our tags fregando Documentation Control Systems, Procedures, Forms and Templates 6 28th September 2006 12:13 PM
Tensile made critical characteristic, but Cpk? High rate of rejection in a part Salman Capability, Accuracy and Stability - Process, Machine, etc. 9 25th May 2006 07:45 PM
Reject Tags - red tag is a form and needs to have a part number and revision? MikeC Documentation Control Systems, Procedures, Forms and Templates 14 25th November 2003 08:49 AM



The time now is 03:55 PM. All times are GMT -4.
Your time zone can be changed in your UserCP --> Options.


   


Marc Timothy Smith - Elsmar.com
8466 LeSourdsville-West Chester Road, Olde West Chester, Ohio 45069-1929
513 341-6272