Elsmar Cove Quality DiscussionsThe Cove Business Standards Discussion Forums More Free Files Forum Discussion Thread Post Attachments Listing Cove Discussion Forums Main Page
UL - Underwriters Laboratories - Health Sciences
Go Back   The Elsmar Cove Business Systems and Standards Discussion Forums >
Forum Username

Elsmar Cove Forum Visitor Notice(s)

Old

"nds" or Number of Discriminate Samples - the Necessary Tool to Work With "ndc"!

Posted 29th March 2018 at 11:28 AM by bobdoering (Bob Doering)
Updated 10th April 2018 at 03:08 PM by bobdoering

By now, you should be aware of the concept of “ndc” or number of discriminate categories that a measurement gage is capable of discerning. It is a statistically significant discrimination, or the capability of telling the difference between items even...
Attached Thumbnails
Click image for larger version

Name:	nds sample data.JPG
Views:	16
Size:	61.2 KB
ID:	50  
bobdoering's Avatar
Stop X-bar/R Madness!!
Views 75 Comments 0 bobdoering is offline
Old

Preparing an X hi/lo-R Chart in Datalyzer

Posted 3rd June 2016 at 03:17 PM by bobdoering (Bob Doering)

Good news! We have verified that the Datalyzer software is capable of doing X hi/lo-R charts for precision machining!
Attached Files: 1. Scan for viruses before opening, 2. Please report any 'bad' files by Reporting this post, 3. Use at your Own Risk.
File Type: docx X hi lo-R charts in Datalyzer.docx (110.9 KB, 234 views)
bobdoering's Avatar
Stop X-bar/R Madness!!
Views 5765 Comments 0 bobdoering is offline
Old

Unilateral Tolerance Capability Calculation

Posted 17th May 2016 at 09:07 AM by bobdoering (Bob Doering)
Updated 2nd December 2017 at 08:59 PM by bobdoering

Capability indices and calculations are tough enough as it is, but a common approach of using Cpu or Cpl ("half Cpk's") is statistically incorrect. It assumes the data is normal - which is unlikely as you approach the physical limit (0 for...
Attached Files: 1. Scan for viruses before opening, 2. Please report any 'bad' files by Reporting this post, 3. Use at your Own Risk.
File Type: pdf unilateral tolerance capability calculation rev 6 120217.pdf (325.8 KB, 87 views)
bobdoering's Avatar
Stop X-bar/R Madness!!
Posted in Uncategorized
Views 5970 Comments 0 bobdoering is offline
Old
Rating: 1 votes, 5.00 average.

INDEX TO CONTENT ON BOB DOERING'S BLOG!

Posted 26th May 2014 at 11:24 AM by bobdoering (Bob Doering)
Updated 3rd June 2016 at 03:20 PM by bobdoering

Here is a handy index for the information in my blog! (Be sure to click Continue reading... below to see the whole page!)

SPC GENERAL

The CORRECT steps to implement an SPC chart


SPC FOR PRECISION MACHINING...
bobdoering's Avatar
Stop X-bar/R Madness!!
Views 6399 Comments 1 bobdoering is offline
Old

Is tool wear a special cause? No...

Posted 26th February 2014 at 09:52 AM by bobdoering (Bob Doering)

Tool wear is common cause. It is a cause intrinsic in the process and can not be eliminated. It affects every part. Special causes are not intrinsic in the process, and do not affect every part - such as tool breakage, start-up, warm-up, etc. It is non-random...
bobdoering's Avatar
Stop X-bar/R Madness!!
Views 3013 Comments 0 bobdoering is offline

Do you find this blog post helpful and informational?

The time now is 06:09 PM. All times are GMT -4.
Your time zone can be changed in your UserCP --> Options.



Misc. Internal Links


NOTE: This forum uses "Cookies"

The Elsmar Cove is currently owned by the Marc Smith Retirement Trust and operated by Law-Nutz Wyoming©2018