The Cove Business Standards Discussion Forums More Free Files Forum Discussion Thread Post Attachments Listing Cove Discussion Forums Main Page
UL - Underwriters Laboratories - Health Sciences
Go Back   The Elsmar Cove Business Systems and Standards Discussion Forums >
Forum Username

Elsmar Cove Forum Visitor Notice(s)

Old

Preparing an X hi/lo-R Chart in Datalyzer

Posted 3rd June 2016 at 03:17 PM by bobdoering (Bob Doering)

Good news! We have verified that the Datalyzer software is capable of doing X hi/lo-R charts for precision machining!
Attached Files: 1. Scan for viruses before opening, 2. Please report any 'bad' files by Reporting this post, 3. Use at your Own Risk.
File Type: docx X hi lo-R charts in Datalyzer.docx (110.9 KB, 100 views)
bobdoering's Avatar
Stop X-bar/R Madness!!
Views 3508 Comments 0 bobdoering is offline
Old

Unilateral Tolerance Capability Calculation

Posted 17th May 2016 at 09:07 AM by bobdoering (Bob Doering)
Updated 18th May 2016 at 08:06 AM by Marc

Capability indices and calculations are tough enough as it is, but a common approach of using Cpu or Cpl ("half Cpk's") is statistically incorrect. It assumes the data is normal - which is unlikely as you approach the physical limit (0 for...
Attached Files: 1. Scan for viruses before opening, 2. Please report any 'bad' files by Reporting this post, 3. Use at your Own Risk.
File Type: pdf unilateral tolerance capability calculation.pdf (152.7 KB, 360 views)
bobdoering's Avatar
Stop X-bar/R Madness!!
Views 3920 Comments 0 bobdoering is offline
Old
Rating: 1 votes, 5.00 average.

INDEX TO CONTENT ON BOB DOERING'S BLOG!

Posted 26th May 2014 at 11:24 AM by bobdoering (Bob Doering)
Updated 3rd June 2016 at 03:20 PM by bobdoering

Here is a handy index for the information in my blog! (Be sure to click Continue reading... below to see the whole page!)

SPC GENERAL

The CORRECT steps to implement an SPC chart


SPC FOR PRECISION MACHINING...
bobdoering's Avatar
Stop X-bar/R Madness!!
Views 4797 Comments 1 bobdoering is offline
Old

Is tool wear a special cause? No...

Posted 26th February 2014 at 09:52 AM by bobdoering (Bob Doering)

Tool wear is common cause. It is a cause intrinsic in the process and can not be eliminated. It affects every part. Special causes are not intrinsic in the process, and do not affect every part - such as tool breakage, start-up, warm-up, etc. It is non-random...
bobdoering's Avatar
Stop X-bar/R Madness!!
Views 2156 Comments 0 bobdoering is offline
Old
Rating: 2 votes, 4.00 average.

The CORRECT steps to implement an SPC chart

Posted 17th November 2010 at 11:46 AM by bobdoering (Bob Doering)
Updated 22nd November 2010 at 05:27 PM by bobdoering

You might have had some SPC training in the past, but it probably skipped over the correct steps to implement charting on the shop floor. Check it out, here they are:

1. Develop the total variance equation (Yes! This is the very first...
bobdoering's Avatar
Stop X-bar/R Madness!!
Views 20679 Comments 16 bobdoering is offline

Do you find this blog post helpful and informational?

The time now is 11:45 PM. All times are GMT -4.
Your time zone can be changed in your UserCP --> Options.


 
 
 


NOTE: This forum uses "Cookies"