The Cove Business Standards Discussion Forums
Thermohygrometer calibration
UL - Underwriters Laboratories - Health Sciences
Thermohygrometer calibration
Thermohygrometer calibration
Thermohygrometer calibration
Thermohygrometer calibration
Thermohygrometer calibration
Thermohygrometer calibration
Thermohygrometer calibration
Thermohygrometer calibration
Thermohygrometer calibration
Go Back   The Elsmar Cove Business Systems and Standards Discussion Forums > > >
Forum Username

Elsmar Cove Forum Visitor Notice(s)

Wooden Line

Thermohygrometer calibration


Monitor the Elsmar Forum
Sponsor Links




Courtesy Quick Links


Links Elsmar Cove visitors will find useful in the quest for knowledge and support:

Jennifer Kirley's
Conway Business Services


Howard's
International Quality Services


Marcelo Antunes'
SQR Consulting, and
Medical Devices Expert Forum


Bob Doering
Bob Doering's Blogs and,
Correct SPC - Precision Machining


Ajit Basrur
Claritas Consulting, LLC



International Standards Bodies - World Wide Standards Bodies

AIAG - Automotive Industry Action Group

ASQ - American Society for Quality

International Organization for Standardization - ISO Standards and Information

NIST's Engineering Statistics Handbook

IRCA - International Register of Certified Auditors

SAE - Society of Automotive Engineers

Quality Digest

IEST - Institute of Environmental Sciences and Technology


Some Related Topic Tags
calibration procedures and methods, thermohygrometer
Reply
 
Thread Tools Search this Thread Rate Thread Content Display Modes
  Post Number #1  
Old 16th May 2018, 04:31 PM
clupin

 
 
Total Posts: 7
Please Help! Thermohygrometer calibration

We use some thermohygrometers to monitor environmental conditions in a controlled environment (medical device manufacturing). We appear to have established some somewhat arbitrary limits a number of years ago. I've never been worried about reaching a limit without someone complaining well beforehand.

When it comes to calibrating equipment of this type and purpose it seems many manufacturers do a single point or two point calibration. I think this is reasonable because the range of operation is very small (50 to 85F) but our quality engineers insist we should be using a 3 point calibration. The cost to do this exceeds the value of the equipment so we are in the position of replacing the equipment instead of calibrating it.

I am curious what other people in the industry are doing.

thanks

Sponsored Links
  Post Number #2  
Old 16th May 2018, 07:44 PM
John Rickey

 
 
Total Posts: 2
Re: Thermohygrometer calibration

We have about 15 thermohygrometers. We also have an environmental chamber that holds temperature very constant and has minimal quick variation in RH. Our strategy is to send one unit out for external calibration and then perform internal calibrations on the other units. We are not FDA regulated, though, which may make a difference here. I would think that with the wide range you do have that an internal calibration would still provide a low enough uncertainty to qualify. You may also be able to shop around for a lower calibration cost (we're charged $150 for 3-point on both T and RH plus $50 if an adjustment is needed).

While buying a new unit is tempting, you need to be cautious--an auditor may ask you to prove the mothballed unit's readings were valid at the end.

Some other thoughts:
1. We have glass thermometers that we calibrate at two points using an ice bath and boiling water.
2. The electronic sensors for T and RH exhibit good linearity. You may be able to do an initial performance qualification of linearity using three points and then do two point external calibrations after that.
3. You may be able to test and show that there is no effect to your product over a much wider range than what is comfortable for your employees. If so, you may be able to justify there is no risk if you do not monitor the T/RH in those processes, then eliminate the requirement or indicate it is for employee comfort only.

One other note: if your units use paper charts be aware that the chart information may be wrong. On a unit where the pen would show an obvious step change for a 1 %RH change, I once saw a chart where there was no step change and there was a 1%RH difference in the reading on opposite sides of the (circular) chart.

John
Thanks to John Rickey for your informative Post and/or Attachment!
Reply

Lower Navigation Bar
Go Back   The Elsmar Cove Business Systems and Standards Discussion Forums > > >

Bookmarks



Visitors Currently Viewing this Thread: 1 (0 Registered Visitors (Members) and 1 Unregistered Guest Visitors)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Forum Search
Display Modes Rate Thread Content
Rate Thread Content:

Forum Posting Settings
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Emoticons are On
[IMG] code is On
HTML code is Off


Similar Discussion Threads
Discussion Thread Title Thread Starter Forum Replies Last Post or Poll Vote
Setting Calibration Tolerance on Gauges - Oven Calibration and Stepped Plug Gage RGohil General Measurement Device and Calibration Topics 10 4th January 2012 12:25 AM
Flow Meter Calibration - Outside Calibration Service vs. In-House Calibration CDISO General Measurement Device and Calibration Topics 3 1st November 2011 08:00 PM
Thermohygrometer Calibration - Number of Required Calibration Points corollax General Measurement Device and Calibration Topics 11 21st June 2010 03:51 PM
Gage pin calibration - Actual calibration readings required on the calibration cert mfr11 General Measurement Device and Calibration Topics 3 9th April 2009 12:58 PM
Calibration Outsourcing vs. In House Calibration - Outrageous Costs of Calibration Cathy Everett General Measurement Device and Calibration Topics 28 5th September 2006 12:50 AM



The time now is 11:49 AM. All times are GMT -4.
Your time zone can be changed in your UserCP --> Options.



Misc. Internal Links


NOTE: This forum uses "Cookies"
The Elsmar Cove web site and all content is owned by Rabbithash Corp. as of 1 MAY 2018.
Unlike Facebook and other properties such as Linkedin, We don't buy, sell, or "share" visitor information. Never have, Never will...
GDPR Compliant since 1996, keeping Marc's vision alive!