The Cove Business Standards Discussion Forums
Measuring a Golf Club Face/Grip/Shaft Rotation
Please read this thread...
Software update
Measuring a Golf Club Face/Grip/Shaft Rotation
Go Back   The Elsmar Cove Business Systems and Standards Discussion Forums > > >
Forum Username

Elsmar Cove Forum Visitor Notice(s)

Wooden Line

Measuring a Golf Club Face/Grip/Shaft Rotation

Monitor the Elsmar Forum
Courtesy Quick Links


Links Elsmar Cove visitors will find useful in the quest for knowledge and support:

Jennifer Kirley's
Conway Business Services


Howard's
International Quality Services


Marcelo Antunes'
SQR Consulting, and
Medical Devices Expert Forum


Bob Doering
Bob Doering's Blogs and,
Correct SPC - Precision Machining


Ajit Basrur
Claritas Consulting, LLC



International Standards Bodies - World Wide Standards Bodies

AIAG - Automotive Industry Action Group

ASQ - American Society for Quality

International Organization for Standardization - ISO Standards and Information

NIST's Engineering Statistics Handbook

IRCA - International Register of Certified Auditors

SAE - Society of Automotive Engineers

Quality Digest

IEST - Institute of Environmental Sciences and Technology


Some Related Topic Tags
measurement (general), measurement techniques and procedures
Reply
 
Thread Tools Search this Thread Rate Thread Content Display Modes
  Post Number #1  
Old 10th August 2018, 06:33 PM
ulle73

 
 
Total Posts: 2
Please Help! Measuring a Golf Club Face/Grip/Shaft Rotation

is there any small device that could measure club face/grip/shaft rotation of the golfclub? needs to be able to measure at high speed

Sponsored Links
  Post Number #2  
Old 14th August 2018, 01:38 PM
ulle73

 
 
Total Posts: 2
Re: Measuring a Golf Club Face/Grip/Shaft Rotation

no one?!
  Post Number #3  
Old 14th August 2018, 02:45 PM
Miner's Avatar
Miner

 
 
Total Posts: 4,351
Look! Re: Measuring a Golf Club Face/Grip/Shaft Rotation

This is fairly complex measurement at a high speed. You will probably need non-contact laser measurement.
Thanks to Miner for your informative Post and/or Attachment!
  Post Number #4  
Old 14th August 2018, 03:13 PM
Marc's Avatar
Marc

 
 
Total Posts: 26,581
Re: Measuring a Golf Club Face/Grip/Shaft Rotation

Quote:
In Reply to Parent Post by Miner View Post

This is fairly complex measurement at a high speed. You will probably need non-contact laser measurement.
I have no idea what the current technology is, but you are undoubtedly correct.

Back in the "old days" for a while I was involved with "air restraint systems" we had a camera that took something wicked like 2000 frames per second but in those days all measurements were "1-D" vs. time.

Last edited by Marc; 14th August 2018 at 03:15 PM. Reason: Correct mistake.
  Post Number #5  
Old 15th August 2018, 06:31 AM
Scanton's Avatar
Scanton

 
 
Total Posts: 55
Re: Measuring a Golf Club Face/Grip/Shaft Rotation

I don’t have an answer, however I am interested and did use high speed imaging for problem solving high speed process errors in a previous employment.
I understand that you are not going to get very far without a reliable datum’s and reliable measurement systems.

It might help to understand what aspects you were trying to quantify. Shaft rotation is probably the easiest to understand as it would be represented as a +/- angle of rotation from a zero point, however what measurement aspects of the “club face” and “grip” were you looking to understand? For example, grip height at point of impact? Horizontal and vertical angle (orientation) of the face at point of impact with the ball? Etc.

With a little more information, you may find some covers will be able to throw some ideas your way.
Reply

Lower Navigation Bar
Go Back   The Elsmar Cove Business Systems and Standards Discussion Forums > > >

Bookmarks



Visitors Currently Viewing this Thread: 1 (0 Registered Visitors (Members) and 1 Unregistered Guest Visitors)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Forum Search
Display Modes Rate Thread Content
Rate Thread Content:

Forum Posting Settings
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Emoticons are On
[IMG] code is On
HTML code is Off


Similar Discussion Threads
Discussion Thread Title Thread Starter Forum Replies Last Post or Poll Vote
Inspection Requirements & Engineering Drawings - Measuring Shaft Dia. Nick-C Inspection, Prints (Drawings), Testing, Sampling and Related Topics 16 6th November 2014 04:02 AM
While Measuring Filter Face, Why We Count From Dead Area? HEPA Filter Related Rajmata Manufacturing and Related Processes 3 19th April 2011 09:25 PM
Variable Measuring Tools for Measuring Centerline of Woodruff Slots in Shaft Work apestate Inspection, Prints (Drawings), Testing, Sampling and Related Topics 7 7th July 2006 09:31 PM
How to determine a machine capability? Measuring results for only one shaft suzi APQP and PPAP 1 16th March 2001 01:49 AM
Production Traceability - Need to Keep Grip On PAULM Manufacturing and Related Processes 4 30th September 2000 12:12 AM



The time now is 12:39 AM. All times are GMT -4.
Your time zone can be changed in your UserCP --> Options.



Misc. Internal Links


NOTE: This forum uses "Cookies"