About calibration gages and poka yokes

G

gabyecc

#1
Hi!
Please help me!.
I'm at the calibration department of an automotive industry and today they ask me to do a list of classification of gages as "doesn't allow to do", "doesn't accept" and "doesn't allow to pass" and I GOT ANGRY! because that are classfications of poka yokes!!! ..... they don't understand the difference between a gage and a poka yoke... i know the classification of a gage are: pressure gages, dial gages, height gages, gages go-nogo.... so i need you to correct me if I am wrong... how can i explain them that? I don't know maybe an example is: the temperature laser gages... I calibrate them to know that the 20°C that the laser measure are really 20°C ... but if that is a laser that getting the measure it doesn't allow the part to pass to the next process is it a poka yoke?
Please help me!! I know a poka yoke doesn't get calibration... poka yokes are verified ... if it get's calibration then are not poka yokes they are gages??
 
Elsmar Forum Sponsor

bobdoering

Stop X-bar/R Madness!!
Trusted Information Resource
#2
I'm at the calibration department of an automotive industry and today they ask me to do a list of classification of gages as "doesn't allow to do", "doesn't accept" and "doesn't allow to pass" and I GOT ANGRY! because that are classifications of poka yokes!!!
Or, at least go/no-go gages

I know a poka yoke doesn't get calibration... poka yokes are verified ... if it gets calibration then are not poka yokes they are gages??

Poka yoke is a very generic term, although it is more specific than go-no go gages in that it assures each part is gaged. However, for all practical purposes, it is a go-no-go gage, and the rabbit parts are standards - which also need controlled. Can it be calibrated? It depends on the specific design, but many can be by verifying them to the print used to manufacture them (is the gate (gage) that allows the part through still 11.500 +/- .003 mm?) using gage blocks, gage pins, etc.
 
Thread starter Similar threads Forum Replies Date
M Procedure or Specification For Extending Gages Calibration Calibration Frequency (Interval) 2
M Calibration of Thread Plugs and Ring Gages - Various Thread Standards General Measurement Device and Calibration Topics 3
A Adjusting Calibration Intervals for Welding related Gages AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 4
J Calibration Recall - Lost Gages procedure example wanted General Measurement Device and Calibration Topics 4
F Checking Gages In and Out and Verifying Calibration Status Calibration and Metrology Software and Hardware 8
D Calibration requirements for New Gages General Measurement Device and Calibration Topics 11
Q Number of Calibration Verification Points - Calipers, height gages, etc General Measurement Device and Calibration Topics 6
C Calibration of Master Thread Plug Gages General Measurement Device and Calibration Topics 2
K Calibration Requirements for Thread and Ring Gages AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 6
D Calibration and Tolerance Ranges of Pressure Gages General Measurement Device and Calibration Topics 8
M Sealed in Wax Thread Gages - ISO 9001 Clause 7.6 Calibration ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 2
J Doing a "yearly" mass calibration of gages over the weekend. Any advice? General Measurement Device and Calibration Topics 4
R Calibration stickers on gages or on boxes? General Measurement Device and Calibration Topics 16
R Calibration Requirements for Employee Owned Gages General Measurement Device and Calibration Topics 5
M Does 17025/NADCAP allow deferring Calibration Start Dates on Gages which are Stored? ISO 17025 related Discussions 10
D Calibration Frequency of Thread Gages use for Aluminium and Stainless Steel Products Calibration Frequency (Interval) 6
D Calibration of Pin Gages using a Calibrated Caliper that measures to 4 decimal places General Measurement Device and Calibration Topics 15
R Environmental Controls Procedure for Calibration of Dimensional Gages General Measurement Device and Calibration Topics 3
N Calibration of Setup Fixtures & Pin Gages General Measurement Device and Calibration Topics 5
M Manufacturing Equipment Pressure Gages Calibration Requirements ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 30
L Do all gages need calibration or only those used for final inspection? General Measurement Device and Calibration Topics 49
D Nonadjustable M&TE - 10 year calibration interval? Pin Gages Calibration Frequency (Interval) 11
mr500 Calibration Of Plug gages (G0-No Go Tri lock gages) General Measurement Device and Calibration Topics 11
S NPT Thread Calibration Method - NPT Taper Thread Plug Gages General Measurement Device and Calibration Topics 9
K Attaching calibration due dates to gages - Sloppy technicians IATF 16949 - Automotive Quality Systems Standard 17
M National Standard for the calibration of angle gages General Measurement Device and Calibration Topics 8
T Calibration and Control - Need help with plug, ring, and thread plug gages General Measurement Device and Calibration Topics 12
K Multiple Gages blocks for calibration General Measurement Device and Calibration Topics 7
M Calibration of ring gages with a CMM General Measurement Device and Calibration Topics 3
J Gaging for Dryseal Pipe Threads (NPTF) and calibration of these gages General Measurement Device and Calibration Topics 11
B Calibration of Home Made Gages - Simple go/no-go gages to true position gages General Measurement Device and Calibration Topics 8
K Suggestions for a Low Cost Accredited Calibration Laboratory - Ring Gages General Measurement Device and Calibration Topics 8
J Calibration of Pin Gages - AS9100 Calibration Requirements General Measurement Device and Calibration Topics 23
M Calibration of employee owned measurement equipment and gages General Measurement Device and Calibration Topics 32
T Plug Gages - How people are maintaining calibration on plug gages General Measurement Device and Calibration Topics 3
H Employee owned gages not entered in calibration system - AS9100 Clause 7.6 AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 16
Ajit Basrur Necessity of Calibration of Manufacturing Process Equipment Gages, Controllers, Etc. General Measurement Device and Calibration Topics 7
G Calibration of 200 sets of Thread Ring Gages - Return them to the manufacturer? General Measurement Device and Calibration Topics 19
J What is an acceptable % of overdue gages not turned in for calibration? General Measurement Device and Calibration Topics 7
J Industry Standard for turning in gages to the Calibration Lab? General Measurement Device and Calibration Topics 2
M Calibration requirements for pins, thread gages, etc? General Measurement Device and Calibration Topics 2
O Calibration tolerances needed - Calipers, digital indicators, feeler gages, etc General Measurement Device and Calibration Topics 4
L Personal Gages and Calibration - Mold department uses personal gages in some aspects General Measurement Device and Calibration Topics 6
C Calibration on gages before Gage R&R Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 6
D Gage Calibration - Non calibrated gages are not used for final dimensions? General Measurement Device and Calibration Topics 3
T Holtest Calibration - Check Points? How many ring gages and sizes? General Measurement Device and Calibration Topics 2
B Calibration Frequency for Rarely Used Gages Calibration Frequency (Interval) 49
M Calibration of Pin Gages - What are my options? General Measurement Device and Calibration Topics 6
M Thread Gage Calibration Software to look up requireds/specs for thread gages Calibration and Metrology Software and Hardware 48
D Illegible Calibration Stickers - Gages used in oily, dirty environment General Measurement Device and Calibration Topics 5

Similar threads

Top Bottom