Acceptability of Perishable Tooling - How do you establish the standards/requirements

Douglas E. Purdy

Quite Involved in Discussions
#1
I am looking for some pointers for those who manufacture perishable tooling. How do you establish the standards/requirements for what product is acceptable and what product is not? How do you deal with product acceptance to an ASME requirement when it gives a general note "95% of drills in any one lot fall within above tolerance" (i.e., for included angle of point, lip height, centrality of web, and flute spacing)? What sampling plans do you utilize in your monitoring of product?

Thanks,
Doug
 
Elsmar Forum Sponsor
Thread starter Similar threads Forum Replies Date
P Risk acceptability alignment between ISO 14971 and IEC 62304 IEC 62304 - Medical Device Software Life Cycle Processes 6
D Rationale for Risk Acceptability Matrix - ISO 14971 ISO 14971 - Medical Device Risk Management 9
I Is risk acceptability really needed if all risks must be reduced as far as possible? ISO 14971 - Medical Device Risk Management 6
A Risk Acceptability Criteria - Probability and Acceptability Level ISO 14971 - Medical Device Risk Management 1
K What is the policy for Risk Acceptability per ISO 14971 ISO 13485:2016 - Medical Device Quality Management Systems 2
Sam Lazzara ISO 14971 Clause 7 - Evaluation of Overall Residual Risk Acceptability ISO 14971 - Medical Device Risk Management 3
bio_subbu US FDA issues Draft Guidance on Premarket Approval (PMA) Acceptability Other US Medical Device Regulations 0
M How to create the Policy for determining criteria for Risk Acceptability ISO 14971 - Medical Device Risk Management 11
B Residual Risk Acceptability - Where do I get this Data/Figures from? CE Marking (Conformité Européene) / CB Scheme 9
I Acceptability of Existing Devices complying to IEC 60601-1 2nd Edition after Jun'2012 IEC 60601 - Medical Electrical Equipment Safety Standards Series 6
A How to Rate a Risk Acceptability and on What Basis is it Measured? ISO 13485 ISO 13485:2016 - Medical Device Quality Management Systems 7
J %Study %Tolerance NDC - R&R Criteria Acceptability when the Tolerance is used Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
L Tools in Gage R&R - Acceptability of an Attribute Gage R&R Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 6
A Correlating Hazard Analysis and DFMEA Risk Acceptability Criteria FMEA and Control Plans 8
T Defining Criteria for Risk Acceptability - ISO 14971 Clause 3.2 ISO 14971 - Medical Device Risk Management 4
B Any Easy Way to determine Linearity Study Acceptability? Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 8
D Understanding ANSI Z1.9 Origin and the Acceptability Constant (k) Inspection, Prints (Drawings), Testing, Sampling and Related Topics 2
R ANSI/ASQ Z1.9 on-line acceptability calculator Other ISO and International Standards and European Regulations 4
M Electrical Assembly Standards - IPC-A-610 "Acceptability for Electronic Assemblies" Various Other Specifications, Standards, and related Requirements 7
T Perishable Tooling Supplier - Nonconformances and Metrics AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 5
QMMike Extrusion Dies - Perishable Tooling? APQP and PPAP 4
E Quality Clause for Purchasing Perishable Materials such as adhesives, primer etc. AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 5
K Perishable Tooling On Receiving Log ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 1
K Tool crib clerk inventories Perishable Tooling - Part Number Tool Lists - Auditable? General Auditing Discussions 2
S Tool change programs for perishable tools IATF 16949 - Automotive Quality Systems Standard 3
D Definition Perishable tooling - Definition - Including PPAP Definition of Perishable tooling Definitions, Acronyms, Abbreviations and Interpretations Listed Alphabetically 7
C Statistical technique sought for predicting replacement of perishable tooling Statistical Analysis Tools, Techniques and SPC 14
Stuart Andrews Perishable vs. Consumable Tooling (4.9.g.1) - What are the differences? QS-9000 - American Automotive Manufacturers Standard 2
C In-process inspection - Tooling and assembly lines for automotive companies AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 6
L Heading dies as "tooling" and AS9100 Manufacturing and Related Processes 2
L Heading dies as "tooling" and AS9100 AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 2
P Definition of production tooling in IATF16949 clause 8.5.1.6 IATF 16949 - Automotive Quality Systems Standard 4
Q Asset / Tooling Management - Two Questions Manufacturing and Related Processes 3
Nicole Desouza AS9100D - Calibration of Dies & Tooling - Plastic Extrusion AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 4
R IATF 16949 Clause 8.5.1.6 a) maintenance and repair facilities - Production tooling management and personnel IATF 16949 - Automotive Quality Systems Standard 4
G Can anyone tell me about Tooling FMEA FMEA and Control Plans 3
S Document control for tooling drawings (Document control clause 7.5.3) IATF 16949 - Automotive Quality Systems Standard 5
S IATF 16949 Supplier Management - Supplier Tooling Requirements Supplier Quality Assurance and other Supplier Issues 1
B PPAP for Disposable Tooling APQP and PPAP 2
T FAI (First Article Inspection) of Large Assemblies/Tooling after move to new building AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 12
A Ensuring Tooling Use Tracking and Traceability AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 1
P Process Validation of inherited tooling by Contract Manufacturer ISO 13485:2016 - Medical Device Quality Management Systems 4
B Need help with a Control Plan for Encapsulation Mold / Trimming / Forming Tooling FMEA and Control Plans 9
R Managing Tooling Condition at Suppliers Supplier Quality Assurance and other Supplier Issues 6
J Tooling Cost - As an OEM I am paying for a new tool Manufacturing and Related Processes 6
E Nadcap - Tooling Control - Major Audit Finding (Question) AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 6
P Machine Shop Tool Crib Procedure - Tooling for CNC mills Quality Tools, Improvement and Analysis 1
P What is a Tooling Detail form? APQP and PPAP 2
W What's the difference between Facility, Equipment and Tooling? APQP and PPAP 1
V GM Gage and Tooling Tolerancing Standards APQP and PPAP 3

Similar threads

Top Bottom