Block 11 of the EASA FORM 1

#1
Hello,

I work for a airplane repair station as Quality engineer.

I have one question about the standard PART 145 :

When and for why we have to put


- Inspected
- Repaired

On the easa form 1 ?

I have a warranty request about a wrong value air flow check on the EASA Form 1 that we sent.


We checked back the part with a flow check and found the same value.

We create and put overhauled on a new EASA form 1 ans send back the aprt.

It is correct ?

Or Should I put "Inspected " on the EASA form 1 ?


Please Help me.
 
Elsmar Forum Sponsor
#2
I would say inspected is a correct statement as overhauled means you made overhaul according to CMM. If you just checked the item then its inspected.
 

AEOS_QA

Involved In Discussions
#3
The FORM 1 should state the maintenance work undertaken on this shop visit.
It should state "Inspected/Tested" (Part-M Appendix II)

Examination, measurement, etc. in accordance with an applicable standard (1) (e.g. visual inspection, functional testing, bench testing etc.)

If you know that it has not been used since you overhauled it, you can add TSO: 0 Hrs in the remarks Block 13
 
Thread starter Similar threads Forum Replies Date
T EASA TAG Block 11 Status/Work issue Quality Manager and Management Related Issues 1
C Gage Block Wringing General Measurement Device and Calibration Topics 3
DuncanGibbons FAA's Building Block approach to certification Inspection, Prints (Drawings), Testing, Sampling and Related Topics 0
A Federal 700B-26 Gage Block Comparator is not reading properly General Measurement Device and Calibration Topics 0
R Master Gage Block Calibration (We have 2 sets) question General Measurement Device and Calibration Topics 3
L Reliability Block Diagrams (RBDs) helper for review. Reliability Analysis - Predictions, Testing and Standards 1
K Height Gage Compensation Block Calibration General Measurement Device and Calibration Topics 1
Sean Kelley Gage Block Verification or buy a new set (cost aspect) General Measurement Device and Calibration Topics 1
J Spherical Bearing Pillow Block ID Measurement General Measurement Device and Calibration Topics 1
T Gage Block Calibration Requirements question General Measurement Device and Calibration Topics 19
I Gage Block Calibration/Measurement Control Question ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 6
K Tolerances on Drawing Title Block Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
D New to Gage Block Calibration Reports Measurement Uncertainty (MU) 6
D Technical Data required in Block 13 (Remarks) or FAA 8130-3 Federal Aviation Administration (FAA) Standards and Requirements 4
F Receiving a new Gage Block Set with an old Certificate Calibration Frequency (Interval) 3
L Terminal Block use in compliance to IEC 60601-1 IEC 60601 - Medical Electrical Equipment Safety Standards Series 3
W Gage Block Interim Test Guidance General Measurement Device and Calibration Topics 5
W Uncertainty Components for Gage Block Comparator Measurement Uncertainty (MU) 2
G Source of a Clear Fixture Block on a x-y Video Microscope - Rafaelco? Inspection, Prints (Drawings), Testing, Sampling and Related Topics 3
A Grade 1 Block Gage Calibration Master General Measurement Device and Calibration Topics 2
Jim Wynne An Oldie but Goodie - A Print Block from 1937 Coffee Break and Water Cooler Discussions 1
K AS9102 - Tolerance Block on Enginerering Drawings to Form 3 of AS 9102 FAIR AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 8
S Questions about AS9102 - Section 5.5.3 & Form 3 block 10 AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 4
V Gage Block Calibration Frequency Requirements Calibration Frequency (Interval) 20
J No Critical Dimensions listed in a Upper Legend Block APQP and PPAP 1
M Block Diagrams and Parameter (P) Diagrams in DFMEA FMEA and Control Plans 3
Marc Block unwanted text messages on your Apple iPhone World News 5
A No Block Tolerance in Print Title Block - Where do I get the tolerance from? Manufacturing and Related Processes 16
K Block Diagram - Requirements for a Block Diagram EU Medical Device Regulations 7
E Gauge Block Grade recommended use for in house calibration General Measurement Device and Calibration Topics 1
A Gage Block Repair - What type of stone is acceptable for removing burrs General Measurement Device and Calibration Topics 5
E Calibration of Calipers, Mics, Height gauges - Recommended Gage Block Types General Measurement Device and Calibration Topics 7
Jerry Eldred Downgrading Tolerance on Gage Block Set General Measurement Device and Calibration Topics 5
O Calibrating a Gage Block In-house with Calibrated Digital Calipers General Measurement Device and Calibration Topics 7
L Smallest Gage block - What is the smallest gage block for calibrating micrometers? General Measurement Device and Calibration Topics 10
C Etalon gage block uncertainty General Measurement Device and Calibration Topics 8
P Corrective Action for ?Mental Block? - ISO 9001 clause 5.5 Internal Communication Nonconformance and Corrective Action 122
B Tolerances on Gage Block Grades General Measurement Device and Calibration Topics 2
S Ultrasonic Thickness Gauge / Step block - Calibration - help General Measurement Device and Calibration Topics 3
P Quality Manual for concrete block manufacturer Quality Management System (QMS) Manuals 4
M Gage Block In-House Calibration - Blocks lost and users keep exchanging blocks General Measurement Device and Calibration Topics 2
V Gage Block Minimum Grade. General Measurement Device and Calibration Topics 2
B Reliablity Block Diagram - RBD Concept Reliability Analysis - Predictions, Testing and Standards 11
C Gage Block Measurement - Home made gage blocks at 1" intervals IATF 16949 - Automotive Quality Systems Standard 7
U FMEA for Service / Diagnostics - Board Level FMEA (at block level not per transistor) FMEA and Control Plans 2
T Gage Block 8D Project - Incorrect Gage Block Orientation General Measurement Device and Calibration Topics 9
QMMike Tolerance block on customer drawing - Major interpretation problem with customer Inspection, Prints (Drawings), Testing, Sampling and Related Topics 25
O Where to purchase Go/NO GO Block gage needed to measure width General Measurement Device and Calibration Topics 5
M Correction for Part/Master material difference in gage block comparison testing General Measurement Device and Calibration Topics 2
J Gage Block Calibration Results and Taking Uncertainty into Account General Measurement Device and Calibration Topics 3

Similar threads

Top Bottom