Calibration of a digital usb temprature probe.

T

Turk 182

#1
We currently use a digital usb temp probe in order to keep our laser trimmer in line. There is currently no calibration procedure to be found regarding this "GoTemp" product. I am currently awaiting response from the company regarding this, but thought that I'd post my dilema here with the hopes of receiving feedback.

Thanks
 
Elsmar Forum Sponsor

BradM

Staff member
Admin
#2
Re: Calibration of a digital usb temp probe.

Hello there, Turk!

You hook this up to a computer through a USB port. Is there some kind of software that reads/ diplays the value? Where do you obtain the temperature?

If there is software, does the software enable you to make adjustments to the probe's calibration/accuracy?
 

Jim Wynne

Staff member
Admin
#3
Re: Calibration of a digital usb temp probe.

We currently use a digital usb temp probe in order to keep our laser trimmer in line. There is currently no calibration procedure to be found regarding this "GoTemp" product. I am currently awaiting response from the company regarding this, but thought that I'd post my dilema here with the hopes of receiving feedback.

Thanks
If the thing that you're using is the same as the one shown here, you can buy eight of them for about what it would cost to have one calibrated. You would also have to supply your calibration provider with the software that comes with the device, or they wouldn't be able to do any readings. If you're contemplating in-house calibration, you'll need to have some sort of traceable standard, and that could get expensive.
 

Jim Wynne

Staff member
Admin
#4
Re: Calibration of a digital usb temp probe.

You might also be interested in this, which is a Consumer Product Safety Commission recall notice for Go!Temp products.
 
Thread starter Similar threads Forum Replies Date
G Calibration of Rotronic probe but not digital readout? General Measurement Device and Calibration Topics 3
D Calibration of Digital thermometer with surface probe General Measurement Device and Calibration Topics 1
A Digital Timer Calibration Requirements General Measurement Device and Calibration Topics 3
D AMS 2750E - Digital Instrument Calibration Accuracy Requirements General Measurement Device and Calibration Topics 1
A Automated calibration of Digital Multimeter without communication port Calibration and Metrology Software and Hardware 2
D Hand-held Digital Tension Meter Calibration General Measurement Device and Calibration Topics 1
J Digital Scale Re-Calibration Interval Frequency General Measurement Device and Calibration Topics 10
M Calibration of Digital Panel Meters General Measurement Device and Calibration Topics 4
W Digital Multi-Meter Calibration Procedure for various Meter Brands and Functions General Measurement Device and Calibration Topics 7
A Fluke Digital MultiMeter Calibration Traceability and Certificate General Measurement Device and Calibration Topics 11
N Thermocouple Calibration - Digital Display vs. Converting the Millivolt into ?C General Measurement Device and Calibration Topics 8
N Digital Temperature Indicator Calibration (Thermocouple) - Using a reference junction General Measurement Device and Calibration Topics 1
T In-House Calibration - Digital Micrometer found Out of Calibration General Measurement Device and Calibration Topics 10
V Calibration of a Digital Vernier - Need to check/calibrate/validate all 3 functions? General Measurement Device and Calibration Topics 9
B Tolerance for Digital Indicator Calibration - Machinists Indicators General Measurement Device and Calibration Topics 1
O Calibration Supplier needed for Digital Temperature/Pressure Controllers General Measurement Device and Calibration Topics 6
O Calibration tolerances needed - Calipers, digital indicators, feeler gages, etc General Measurement Device and Calibration Topics 4
S Safeguarding Calibration on Digital Equipment General Measurement Device and Calibration Topics 25
F Digital Multimeter - Verification vs. Calibration MSA (Measurement System Analysis) Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
J Digital Caliper Calibration vs. Verification - Full Scale vs. Used Range General Measurement Device and Calibration Topics 8
C Is calibration of digital panel important in any semicon company? General Measurement Device and Calibration Topics 3
M Calibration of Timers to NIST - How are digital and analog timers calibrated? General Measurement Device and Calibration Topics 15
lanley liao Question regarding the calibration of monitoring and measure equipment. Oil and Gas Industry Standards and Regulations 0
N IATF Calibration Lean in Manufacturing and Service Industries 3
Q Do these certificates of calibration meet ISO 9001 requirements for traceability to NIST? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 10
T Plug Gage Calibration Calibration and Metrology Software and Hardware 1
M Load Cell Calibration using a totalizer on a flow meter General Measurement Device and Calibration Topics 0
E Calibration Records needed ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 1
D Limited Range Calibration - 5000 lb Industrial floor scale General Measurement Device and Calibration Topics 3
D Calibration of Small Scales General Measurement Device and Calibration Topics 26
C How to Establish the Calibration & Measurement Capability (CMC)? ISO 17025 related Discussions 1
I IQOQ or just initial calibration required? General Measurement Device and Calibration Topics 3
B Calibration in real life ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 3
J Calibration cycle for monitoring & measuring tools used in medical device manufacturing General Measurement Device and Calibration Topics 5
A Is calibration of test weight required General Measurement Device and Calibration Topics 4
S Calibration Frequency for Slip Gauge Kit used for CMM Calibration? General Measurement Device and Calibration Topics 0
S Calibration/Verification of customer fixtures IATF 16949 - Automotive Quality Systems Standard 6
Ron Rompen Calibration by manufacturer ISO 17025 related Discussions 4
Q Calibration verification records 7.1.5.2.1 IATF 16949 - Automotive Quality Systems Standard 2
B AS9100D 7.1.5.2 Calibration or Verification Method using outside cal lab AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 1
W Next Calibration Due Date Calibration Frequency (Interval) 5
S Where do l get calibration standards to run a calibration lab? Other ISO and International Standards and European Regulations 2
A OEM On-Site Calibration issues during Covid19 ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 12
D Calibration tolerance question using Pipettes Medical Device and FDA Regulations and Standards News 1
M Calibration Certificate Result issued by an accredited external laboratory General Measurement Device and Calibration Topics 9
G Calibration of "Master Parts" Used as Gauges Calibration Frequency (Interval) 5
R Calibration lab environmental monitoring General Measurement Device and Calibration Topics 4
F Standard Calibration Procedures: Recommended Practice ISO 17025 related Discussions 0
T Temperature Requirements For In House Calibration - AS9100 AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 16
B Gage calibration frequency, ISO and IATF - What are the requirements Calibration Frequency (Interval) 3

Similar threads

Top Bottom