SBS - The Best Value in QMS software

Calibration of Plug Gauges - Tolerancing

#1
Morning!
I am about to start calibrating our plug gauges in house and could do with some advice please. Our company conforms to ISO9001:2015 and I have found the standard BS696:1982 online to help with tolerancing. However I have become a little confused.

For example, The plug gauge I am calibrating has the limits of Go (1.150mm) and No/Go (1.250mm). I have measured each plug and have gotten then an average reading (Go-1.1508 and No/Go – 1.2434). However reading the BS696 standard, I am unsure of what the tolerance for this type of plug gauge is i.e +/- 0.001mm etc.

Does anyone have any advice or would you be able to point me in the right direction? Much appreicated!
 

Attachments

Last edited by a moderator:
Elsmar Forum Sponsor

ScottK

Not out of the crisis
Staff member
Super Moderator
#2
Thread starter Similar threads Forum Replies Date
B Method for Calibration of Thread Plug Gauges General Measurement Device and Calibration Topics 13
R Setting Calibration Tolerance on Gauges - Oven Calibration and Stepped Plug Gage General Measurement Device and Calibration Topics 10
Geoff Cotton ISO 6H Go Screw Plug Gauges Calibration to ANSI / B1.16M vs BS 3643 General Measurement Device and Calibration Topics 5
T Plug Gage Calibration Calibration and Metrology Software and Hardware 1
C Calibration of Master Thread Plug Gages General Measurement Device and Calibration Topics 2
D Indysoft Calibration Software Thread Plug Template Help General Measurement Device and Calibration Topics 2
G Gage Recall Analysis - Threaded Plug Gage has failed Calibration General Measurement Device and Calibration Topics 10
M Thread Plug Gage - Calibration Frequency ISO 13485:2016 - Medical Device Quality Management Systems 1
L Calibration Procedure for Internal Spline Plug Gage Needed General Measurement Device and Calibration Topics 4
R Thread Measurement - Basics on Thread Plug and Ring Calibration General Measurement Device and Calibration Topics 5
mr500 Calibration Of Plug gages (G0-No Go Tri lock gages) General Measurement Device and Calibration Topics 11
S NPT Thread Calibration Method - NPT Taper Thread Plug Gages General Measurement Device and Calibration Topics 9
T Calibration and Control - Need help with plug, ring, and thread plug gages General Measurement Device and Calibration Topics 12
R Calibration Check Points for ACME & LPT Thread Plug & Rings General Measurement Device and Calibration Topics 5
P Plug Gage Calibration Report does not include actual data - ISO 9001:2000 section 7.6 General Measurement Device and Calibration Topics 3
T Plug Gages - How people are maintaining calibration on plug gages General Measurement Device and Calibration Topics 3
J Confused about Calibration Tolerances of Plug Gauge, Ring Gauge & Snap Gauge General Measurement Device and Calibration Topics 4
T Threaded plug and ring gage calibration procedures General Measurement Device and Calibration Topics 4
P Thread plug gauge failed calibration - Must I remeasure everything measured with it? General Measurement Device and Calibration Topics 23
D Plug Gage Calibration - Manufacturer's Certification vs. Calibration Laboratory General Measurement Device and Calibration Topics 2
S Failed Calibration - Plain Plug Gages - They grow! General Measurement Device and Calibration Topics 24
U Calculate acceptance of equipment reading after calibration General Measurement Device and Calibration Topics 2
D Question on Documented Calibration versus ISO 17025 Accredited Calibration ISO 13485:2016 - Medical Device Quality Management Systems 0
U Calculate acceptance of calibration reading Measurement Uncertainty (MU) 1
D Air hood calibration ISO 13485:2016 - Medical Device Quality Management Systems 1
K Ground Bond Test for Class I Medical Electrical Equipment - calibration problems IEC 60601 - Medical Electrical Equipment Safety Standards Series 2
E Calibration/Verification Report Durometer ISO 17025 related Discussions 2
S Medical device equipment calibration Qualification and Validation (including 21 CFR Part 11) 1
J Scrap Material Scale Calibration Required? IATF 16949 - Automotive Quality Systems Standard 21
S 7.1.5.2.1 Calibration/Verification Records IATF 16949 - Automotive Quality Systems Standard 6
K Is Calibration Required for Non-Adjustable Commercial Inspection Devices? General Measurement Device and Calibration Topics 11
F Calibration in GPC/SEC General Measurement Device and Calibration Topics 1
Q Changing calibration frequency Calibration and Metrology Software and Hardware 18
M IATF 16949 SI # 10: Integrated self-calibration of measurement equipment- Needs for explanation IATF 16949 - Automotive Quality Systems Standard 2
M Storing Calibration Certificate Document Control Systems, Procedures, Forms and Templates 7
B Risk analysis for defective measuring or measuring equipment out of calibration General Measurement Device and Calibration Topics 2
S Placing a calibration sticker with someone other than your initials Records and Data - Quality, Legal and Other Evidence 8
J IATF 16949 Calibration/Verification records question ISO 26262 - Road vehicles – Functional safety 5
M Approval of Calibration Certificates General Measurement Device and Calibration Topics 1
lanley liao Question regarding the calibration of monitoring and measure equipment. Oil and Gas Industry Standards and Regulations 3
N IATF Calibration Lean in Manufacturing and Service Industries 5
Q Do these certificates of calibration meet ISO 9001 requirements for traceability to NIST? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 12
M Load Cell Calibration using a totalizer on a flow meter General Measurement Device and Calibration Topics 0
E Calibration Records needed ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 1
D Limited Range Calibration - 5000 lb Industrial floor scale General Measurement Device and Calibration Topics 3
D Calibration of Small Scales General Measurement Device and Calibration Topics 32
C How to Establish the Calibration & Measurement Capability (CMC)? ISO 17025 related Discussions 1
I IQOQ or just initial calibration required? General Measurement Device and Calibration Topics 3
B Calibration in real life ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 3
J Calibration cycle for monitoring & measuring tools used in medical device manufacturing General Measurement Device and Calibration Topics 5

Similar threads

Top Bottom