Can identical gages in different facilities be in the same family?

#11
Another GR&R is what the auditor wants. The feature is on the control plan even though it's not an SC - if it's on the control plan you have to have an R&R - that's a given. My alternate approach is to take it off the control plan.
What bothers me most about this is the cost of this R&R.
50 parts measured on CMM - $937.50
3 operators measuring 50x3 parts - $1125
QE project time - $320
TS Auditor satisfaction - PRICELESS!
Not the satisfaction of this auditor! I wouldn't spend that money doing the GR&R. He stated the process wasn't effective. You can show it's the other way. A CB is a supplier and they've delivered you a report which is lacking in someway. Push it back...it's the right thing to do, at very least to get clarification on why this is ineffective! It's all fine and dandy for an auditor to say it is, but the report should give evidence to back it up!
 
Elsmar Forum Sponsor
Thread starter Similar threads Forum Replies Date
M Validation of two nearly identical products Other Medical Device Regulations World-Wide 5
L Gage R&R studies for identical Devices - Need to confirm the requirement to perform them Reliability Analysis - Predictions, Testing and Standards 2
M Identical Sales Package in Different Countries Pharmaceuticals (21 CFR Part 210, 21 CFR Part 211 and related Regulations) 0
S Minitab runs at different speeds on identical PCs Using Minitab Software 5
G How to Fix Mis-Identified Dimensionally Identical Parts Nonconformance and Corrective Action 5
A Two Identical Medical Devices put in different Classes - Class I and Class II 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 2
D Back to Back MSA - Two "identical" automatic measuring systems Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
I Are IEC 60601-1:2012 and BS EN 60601-1:2006+A11:2011 still identical? IEC 60601 - Medical Electrical Equipment Safety Standards Series 2
Q Auditor found Form with Identical Contents but different Format - is this an NC? Document Control Systems, Procedures, Forms and Templates 28
D Recall, Safety Notice or Training? - Medical Device with two identical complaints 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 15
Q Repeating Identical Processes in different Procedures? Document Control Systems, Procedures, Forms and Templates 8
C Equivalence Studies - Validation Activities for several Identical Pieces of Equipment Manufacturing and Related Processes 1
C Equivalence Studies - Validation Activities for several Identical Pieces of Equipment Qualification and Validation (including 21 CFR Part 11) 2
Icy Mountain TS 16949 Requirement for New MSA for Identical Replacement Part Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 7
D How to audit identical processes? TS 16949 Clause 8.2.2 General Auditing Discussions 2
N Hypothsis test - Problem with an in-process test machine - Almost identical product Statistical Analysis Tools, Techniques and SPC 7
D Gage R&R on one tape measure to represent all identical tapes Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 1
P How many SPC charts for Bolt Torque? 4 identical Nut/Bolts in the same part Statistical Analysis Tools, Techniques and SPC 14
N % Tolerance - Type 1 study on the gages, then a gage R&R (ANOVA) Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
S Formula for Calculating NoGo Major Diameter for UN gages Inspection, Prints (Drawings), Testing, Sampling and Related Topics 4
D Preventative Maintenance for Gages, handtools etc Other Medical Device Regulations World-Wide 1
M Procedure or Specification For Extending Gages Calibration Calibration Frequency (Interval) 2
M How to verify profile gages provided by customer General Measurement Device and Calibration Topics 5
PastorBee13 Source for the blades for Reef Snap Gages General Measurement Device and Calibration Topics 2
M AS9100 Rev D and Pin Gages General Measurement Device and Calibration Topics 7
M Calibration of Thread Plugs and Ring Gages - Various Thread Standards General Measurement Device and Calibration Topics 3
D Cp/Cpk on Gages for MSA (vs. Cg/Cgk) Capability, Accuracy and Stability - Processes, Machines, etc. 21
A Adjusting Calibration Intervals for Welding related Gages AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 4
J Calibration Recall - Lost Gages procedure example wanted General Measurement Device and Calibration Topics 4
Q Is it normal practice to lubricate Ring Gages before use? General Measurement Device and Calibration Topics 17
T How to Calibrate Taper Gages General Measurement Device and Calibration Topics 1
C Manufacturing Thread Ring Gages Manufacturing and Related Processes 3
C Measuring Solid Thread Ring Gages General Measurement Device and Calibration Topics 17
P Best Method of Cleaning of Thread Ring Gages Calibration Frequency (Interval) 5
M Control Plan MSA's - Pressure Gages IATF 16949 - Automotive Quality Systems Standard 2
C Implementing a set of bore gages at a machine Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 1
F Checking Gages In and Out and Verifying Calibration Status Calibration and Metrology Software and Hardware 8
D Calibration requirements for New Gages General Measurement Device and Calibration Topics 11
Q Number of Calibration Verification Points - Calipers, height gages, etc General Measurement Device and Calibration Topics 6
C Calibration of Master Thread Plug Gages General Measurement Device and Calibration Topics 2
C Measurements of Major Diameters of plug thread gages General Measurement Device and Calibration Topics 12
J Verification of Gages Before Use Calibration Frequency (Interval) 10
L Inexpensive Gage Management Software recommendations for less than 75 Gages Calibration and Metrology Software and Hardware 8
T How do I calibrate NPT Thread Plug Gages? General Measurement Device and Calibration Topics 9
V How to measure radius without radius gages APQP and PPAP 4
N When and which gages require a Gage R&R study? Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 9
K Calibration Requirements for Thread and Ring Gages AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 6
BHobbs_Busche ISO/TS16949:2009 - MSA requirements for common gages IATF 16949 - Automotive Quality Systems Standard 5
D Calibration and Tolerance Ranges of Pressure Gages General Measurement Device and Calibration Topics 8
M Calibrating Digital Pressure Gages In-House General Measurement Device and Calibration Topics 10

Similar threads

Top Bottom