Determination of Test Cycles of Dynamic Forces (IEC 60601)

#1
Hi cove,
:(
There is no definition of test cycle of dynamic forces stated in clause 9.8.3.3 of IEC 60601-1:2012. Well, how to determin the test cycle ? which may be effect the test result of the product.

I find IEC 60601-2-52 (medical bed) clause 201.9.8.3.3 do well. It specified the test cycle is 10000times. But the device is not a medical bed.

So, how to deal with this situation in IEC 60601-1:2012???:deadhorse:
Can i use the life time of the device to decide the test cycle??

Everyone has good point?
I appreciated your joining :applause:
 
Elsmar Forum Sponsor
N

NickM

#2
If the number of cycles is not specified in the standard, than the test only needs to be performed one time unless your risk management process dictates otherwise.
 
Thread starter Similar threads Forum Replies Date
S Shelf Life Determination - Sterility test (Stasis test) ISO 13485:2016 - Medical Device Quality Management Systems 12
A Destructive Test Sample Size Determination Statistical Analysis Tools, Techniques and SPC 4
N Thermocouple Drift Determination - Drift test done by NIST General Measurement Device and Calibration Topics 3
D Standard guide for shelf life determination of non sterile component with degradation materials Reliability Analysis - Predictions, Testing and Standards 1
M EU IVD Risk Determination of sample collection EU Medical Device Regulations 0
cscalise Determination of CPD (Continuing Professional Development) hours for a training course Training - Internal, External, Online and Distance Learning 1
C AS9138 Sample Size Determination AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 1
T Determination of TENSION SAFETY FACTORS - Table 21 IEC 60601-1 Other Medical Device Regulations World-Wide 5
J Interesting Discussion Sample Size Determination for Medical Device Other Medical Device and Orthopedic Related Topics 9
H Max and Min Load Determination for Steam Sterilization of Liquds EU Medical Device Regulations 1
V When and How to apply the Bayes Success Run approach for Sample Size Determination Inspection, Prints (Drawings), Testing, Sampling and Related Topics 4
R Determination of IP (International Protection Marking) Rating IEC 60601 - Medical Electrical Equipment Safety Standards Series 3
Marc Determination of Sample Sizes when Auditing General Auditing Discussions 13
V Determination of the Optimal Sampling Number Inspection, Prints (Drawings), Testing, Sampling and Related Topics 7
J Root Cause Determination Training for Production Managers Nonconformance and Corrective Action 6
somashekar Determination of Clean Room Class for Medical Devices ISO 13485:2016 - Medical Device Quality Management Systems 1
G Determination of dental plaque disclosing products Other ISO and International Standards and European Regulations 1
A Determination of Production Equivalence for Design Validation 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 1
kedarg6500 Determination of Metal Grade from known Chemical Composition Inspection, Prints (Drawings), Testing, Sampling and Related Topics 4
S Root Cause Determination of Epoxy Encapsulated Electronics Modules Nonconformance and Corrective Action 8
P Determination of Subgroup Size for P Charts Statistical Analysis Tools, Techniques and SPC 4
GStough 7.2.1 Determination of req'ts related to the Product...in Contract/Service Industry Service Industry Specific Topics 2
M 8.2.2 Internal Audit - Determination of Effective Implementation IATF 16949 - Automotive Quality Systems Standard 4
N Chemical Oxygen Demand (COD) Determination in Industrial Waste Water General Measurement Device and Calibration Topics 5
J How IAQG plans to ensure that correct PEAR level determination is done by Auditors? AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 8
L Determination of AMS 2750D Furnace Classifications AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 8
sagai New Draft Guidance from FDA - Factors considered for Risk/Benefit Determination Other US Medical Device Regulations 4
Statistical Steven Continuous Data Analysis Sample Size Determination Six Sigma 3
M AS9100 Rev C Initial Certification - Determination of Competence AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 3
K Determination of Calibration Frequency by an Outside Laboratory Calibration Frequency (Interval) 5
S Medical Device Software Level of Concern Determination 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 23
E Differences between "Significant Change" determination - Canada vs. FDA Canada Medical Device Regulations 3
N ISO 34: Rubber, vulcanized or thermoplastic - Determination of tear strength Other ISO and International Standards and European Regulations 1
T Determination of UMDNS Code for various types of Contact Lens ISO 13485:2016 - Medical Device Quality Management Systems 4
P SPICE (Software Process Improvement and Capability Determination) Certification Software Quality Assurance 3
6 Method for Determination of Amount of Air in Orange Juice Manufacturing and Related Processes 7
S Electronic Coordinate Determination System Inspection, Prints (Drawings), Testing, Sampling and Related Topics 21
S Criteria for Determination of Significant Aspect/Hazard in IMS Miscellaneous Environmental Standards and EMS Related Discussions 3
M Environmental Aspect Significance Determination and Scoring Miscellaneous Environmental Standards and EMS Related Discussions 6
E ISO14971 - Determination of possible hazards (SU, UU, PC) ISO 14971 - Medical Device Risk Management 3
J Documentation of the determination that an NCMR is invalid ISO 13485:2016 - Medical Device Quality Management Systems 4
R New Equipment Calibration and determination of Calibration Frequency General Measurement Device and Calibration Topics 8
P Repetition (sample size) for measuring equipment accuracy determination General Measurement Device and Calibration Topics 1
B Clause 7.2.1 Determination of requirements related to the product ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 5
T AS9003 vs AS9100 vs ISO9001:2008: Making a QMS Determination Quality Manager and Management Related Issues 5
K Sample Size Determination - Medical Devices Inspection, Prints (Drawings), Testing, Sampling and Related Topics 4
A Emergency Preparedness and Response Procedure Criteria Determination Miscellaneous Environmental Standards and EMS Related Discussions 3
R Sample determination using minitab if everything elses is a variable Inspection, Prints (Drawings), Testing, Sampling and Related Topics 3
L Determination of Root Cause for Preventive Actions Problem Solving, Root Cause Fault and Failure Analysis 41
S Clauses 6.1 and 6.4 questions - "Determination" aspects AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 2

Similar threads

Top Bottom