SBS - The Best Value in QMS software

Effects of Strengthened Surveillance of Notified Bodies in 2015

J0anne

J0anne

Joanne
#1
#1
With the strengthened surveillance of Notified Bodies imminent, what do you think will be the greatest challenges facing medical device manufacturers in 2015?
 
Free Trial of DISCUS Desktop
Elsmar Forum Sponsor
You must log in or register to reply here.
Thread starter Similar threads Forum Replies Date
K Monitoring the identified side-effects and contraindications ISO 14971 - Medical Device Risk Management 4
Q Determining Adverse Effects of Corrective/Preventive Actions ISO 13485:2016 - Medical Device Quality Management Systems 2
Watchcat Effects of Technology - 2020 Misc. Quality Assurance and Business Systems Related Topics 14
C Failure nets - Same level effects FMEA and Control Plans 0
M Informational US FDA paper – Epidemiological Evidence on the Adverse Health Effects Reports in Relation to Mercury from Dental Amalgam: Systematic Literature Review Medical Device and FDA Regulations and Standards News 0
C Detection Action for Failure Effects - AIAG 4th Edition Layout FMEA and Control Plans 5
J0anne Implantable Devices - The effects of surgical scaffold implanted into the human body Other Medical Device and Orthopedic Related Topics 8
H Addressing of Undesirable side-effects, harms, risks and side-effects in clinical evaluation report (CER) EU Medical Device Regulations 12
B ISO 9001:2015 6.1.1 b - Enhance desirable effects - No opportunities were addressed ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 10
I DOE: High variance and small effects in Minitab Using Minitab Software 1
T How to Document Risk Effects on Design Change(s) ISO 14971 - Medical Device Risk Management 3
J Medical Device Failure Effects - Where to draw the line? FMEA and Control Plans 8
kedarg6500 Potential Effects of Failure(s) FMEA and Control Plans 23
P UFMEA - Use Failure Mode Effects Analysis FMEA and Control Plans 7
Q Format to Evaluate the Effects of New Processes and Equipment Manufacturing and Related Processes 4
R Effects of Calibration Laboratory Temperature on Uncertainty Measurement Uncertainty (MU) 10
A Effects of categorical variables on single response Using Minitab Software 9
J Quality Management Process Model Possible Interactions and Effects ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 1
L "Half Normal Plot vs Normal Probability Plot" of Effects Using Minitab Software 1
R Drawing a Normal Plot of the Effects for Multilevel Factorial Design Using Minitab Software 3
E Laser Marking effects on the Fatigue Strength of Alloys CE Marking (Conformité Européene) / CB Scheme 6
A Function for Effects - Beginner in usage of the IQRM FMEA and Control Plans 3
M Corporate Procedures and their effects on Companies they Own Quality Manager and Management Related Issues 6
Q Documenting the Review of Adverse Effects from Rework ISO 13485:2016 - Medical Device Quality Management Systems 4
B Process FMEA (PFMEA) Same Multiple Causes for Different Effects FMEA and Control Plans 6
P Adverse Effects caused by Manufacturing Material of Medical Devices Manufacturing and Related Processes 4
S Effects of Irradiation Sterilization on Medical Electronics - Li Coin Cell Batteries IEC 60601 - Medical Electrical Equipment Safety Standards Series 5
R Are multi-faults needed? Effects of a Short Circuit IEC 60601 - Medical Electrical Equipment Safety Standards Series 7
S Nylon Moisture Content - Transportation and Seasonal Effects Manufacturing and Related Processes 3
AnaMariaVR2 Effects of the Economic Downturn in Quality Systems & Quality in General Career and Occupation Discussions 9
G Effects of CMM Probe Tip Ball Size measuring a Round Part OD - CMM Help Inspection, Prints (Drawings), Testing, Sampling and Related Topics 18
R Effects of Dealing with Out of Tolerance Monitoring Equipment General Measurement Device and Calibration Topics 4
M New Directive MDD 2007/47 - What is the status and effects? EU Medical Device Regulations 7
D ITAR/EAR and effects on commercial Heat Treating AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 2
H Removing fixed effects (time demeaned variables) in Minitab Using Minitab Software 12
S Process Failure Mode Effects Analysis (PFMEA) Basics FMEA and Control Plans 4
M PAA (Process Assurance Assessment) vs. FMEA (Failure Modes and Effects Analysis) FMEA and Control Plans 3
Raffy Effects or Impact of Changes to ISO 17021 and Revision Status as of 16 NOV 2014 Other ISO and International Standards and European Regulations 25
J Effects of substrate on biological indicator organisms US Food and Drug Administration (FDA) 2
Q FMEA (Failure Modes and Effects Analysis) and Control Plan Process Diagrams FMEA and Control Plans 3
S What is the use of bar code? The Potential Effects of Missing Bar Code Labels FMEA and Control Plans 6
S Basic PFMEA (Process Failure Mode Effects and Analysis) Questions FMEA and Control Plans 22
T Standard for "Simulating Long Term Effects on Materials / Thermal Disinfecion" needed Other ISO and International Standards and European Regulations 3
T The Effects of Anodization on Pressure Impregnated Castings Manufacturing and Related Processes 3
R Should I be notifying the FDA of adverse effects (per 21 CFR 803)? ISO 13485:2016 - Medical Device Quality Management Systems 4
M Difference between potential failure mode and potential effects of failure FMEA and Control Plans 11
D ISO 14971 Risk Analysis - Effects of component failure on the patient ISO 14971 - Medical Device Risk Management 7
B Grain boundary effects in alloy depletion analysis - SAE AS7101 requirement AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 1
A How to organize DFMEA for Failures that have many Causes and Effects FMEA and Control Plans 2
F Quality Management System vs. Effects of Local Culture on Implementing a QMS Misc. Quality Assurance and Business Systems Related Topics 22

Similar threads

Top Bottom