Gage R&R Form in Excel for Calculating Gauge R&R - Attached

automoto

Involved In Discussions
#31
Very nice clean interface. Do you plan to update to MSA 4th edition as well? Your good work would need only a couple of tweaks as the 4th edition does more clearly differentiate between Product and Process GR&R and acceptable % and also modified the 0-30% rule.

Capability comparison and rationale demonstrated that 0-30% error has a neglible effect on Ppk/Cpk estimates. It was noted that capability percentage uses 30% as derived from σ; when the σ² (variance) is used, the maximum is 10%. Over 30% the effect on accept/reject decisions is almost exponential. (Appendix B, Page 199).

Thanks!
Hi,

I have in plan to add on the form calculation of PV from historical variation informations (Pp). See page 121. Also calcualtion described in appendix B will be added. Thans for your proposal.
What you mean under 0-30% rule? GRR criteria all the same as in MSA 3rd version, right? Page 78.

Form update will be made in one month.
Regards
 
Elsmar Forum Sponsor

automoto

Involved In Discussions
#32
Hi automoto,

Just another question about your MSA Excel file:
I used it a couple of times now, but i wonder if it is not to be needed to fill in the minimal gage resolution ? For example when using a digimatic caliper fill in minimal gage resolution 0,01 mm or when using a micrometer fill in minimal gage resolution 0,001 mm etc.

cheers

Mr.Happy
Hi Mr. Happy,

If gauge resolution is OK tells you ndc index. Do you want that I add on the form data about gauge resolution?


Regards
 
M

Mr.Happy

#33
Hi Mr. Happy,

If gauge resolution is OK tells you ndc index. Do you want that I add on the form data about gauge resolution?


Regards
Hi again,

For customers or auditors it would be better that one can see on the MSA study what the resolution of the used gage is.
Also would it be nice that there is a statement on the form about the gage resolution, something like:
"Resolution is sufficient (resolution =<5% of the tolerance!)": Resolution is not sufficient!"
or something like that.

I will attach a xls form as an example, see page GRR Report cel L11 and K14

Keep up the good work.

Mr.Happy :cool:
 

Attachments

K

kevyeoh

#35
very nice form...
but for a newbie like me, it is a bit hard to understand which information i should enter...is there a readme guide to explain or show some sample where we can include what type of information?

Thanks.
 

harry

Super Moderator
#36
............ but for a newbie like me, it is a bit hard to understand which information i should enter...is there a readme guide .....................
Welcome to the Cove.

Such forms should normally be read in conjunction with the relevant version of the MSA Manual. You should find what you want inside there.
 
M

Mr.Happy

#37
Hi,

I update form to MSA 4th edition. If someone found some nonconformity in calculations plese inform me.

Thanks
Hi Automoto,

1) Your new sheet is protected can not fil in all cels.
2) NDC is again 13, should be 14 ?!

Cheers,

Mr.Happy.
 
D

dbulak

#40
What do you enter in the box for "gage discrimination" and "unit"? Also, entering a gage measurement eg. .03125, it automatically rounds up.
 
Thread starter Similar threads Forum Replies Date
T Gage R&R Excel .xls form and SPC Xbar and R template (lost it.. ) Excel .xls Spreadsheet Templates and Tools 13
I Gage R&R Form - Excel or other - Calculations Questions Excel .xls Spreadsheet Templates and Tools 13
A What should be the contents of the New Gage Introduction Form ? General Measurement Device and Calibration Topics 3
U Root Cause for a Form not having all info (traceability standard and the gage number) Problem Solving, Root Cause Fault and Failure Analysis 14
H Gage R&R Data Collection Form w/ Appraisers Names, Number of Parts, Number of Trials Document Control Systems, Procedures, Forms and Templates 2
M AS9100 Gage R&R Form Needed Document Control Systems, Procedures, Forms and Templates 6
M Gage R&R form for 2 operators 10 parts and 3 trials needed Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 1
S GD&T Rule 1: Gage size for form check at MMC (maximum material condition)? Inspection, Prints (Drawings), Testing, Sampling and Related Topics 9
B Gage calibration form needed Document Control Systems, Procedures, Forms and Templates 8
P Gage Repeatability (1x1x10) form - 1 part measured 10 times by 1 appraiser Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 7
Q Gage R&R lite? This form only uses two operators measuring five parts one time Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 10
M Attribute Gage R&R Form - Long Version - AIAG's MSA Manual Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 35
T Plug Gage Calibration Calibration and Metrology Software and Hardware 1
L Gage R&R TMV Acceptance Criteria Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
S MSA for attribute relation gage Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
E Zero part to part variation - Gage R&R project Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 15
M Gage R&R and right way to measure Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 16
L Gage RandR on automated equipment. IATF 16949 - Automotive Quality Systems Standard 7
B Gage calibration frequency, ISO and IATF - What are the requirements Calibration Frequency (Interval) 3
D Difference between Test Method Validation and Gage R&R Qualification and Validation (including 21 CFR Part 11) 18
R Determining Uncertainty from Gage R&R Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 1
C Correct Calibration Method for Dial Depth Gage General Measurement Device and Calibration Topics 6
C Gage Block Wringing General Measurement Device and Calibration Topics 3
B Gage R&R with NDC=1 Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 19
S Type 1 Gage R&R or something else? Reliability Analysis - Predictions, Testing and Standards 6
G Should I perform Gage R&R only at the beginning of a new project? Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 6
V Thread Plug Gage Pitch GO Diameter out of spec AQL - Acceptable Quality Level 8
G Gage R&R - Where am I going wrong? Part of a FAIR submission (Aerospace) Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
R Gage R&R Excel templates Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
K Gage R&R with more than 3 appraisers Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
Anerol C Gage R&R Template AIAG 4th Edition IATF 16949 - Automotive Quality Systems Standard 3
T Attributes SPC study - Attributive control (Go gage) Statistical Analysis Tools, Techniques and SPC 5
S Capability or Gage R&R Study for Leak Tester? Reliability Analysis - Predictions, Testing and Standards 15
N % Tolerance - Type 1 study on the gages, then a gage R&R (ANOVA) Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
M Definitive answer on Type 1 vs Type 2 vs Type 3 Gage Study Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 0
V Gage Management and Gage R&R Software General Measurement Device and Calibration Topics 1
D Gage R&R Study on Load Cells - Large chemical blending tanks IATF 16949 - Automotive Quality Systems Standard 1
B Minitab Type 1 Gage Study on True Position Question Measurement Uncertainty (MU) 1
S Gage R&R on alloy Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 10
8 Need Help - Runout - Function Gage Inspection, Prints (Drawings), Testing, Sampling and Related Topics 7
L Gage R&R studies for identical Devices - Need to confirm the requirement to perform them Reliability Analysis - Predictions, Testing and Standards 2
G Stab Pin Size For Check Gage Inspection, Prints (Drawings), Testing, Sampling and Related Topics 3
E Functional Gage for TOP applied at RFS Design and Development of Products and Processes 5
F No reproducibility Error in Gage R&R? Reliability Analysis - Predictions, Testing and Standards 4
M Template for Attribute Gage R & R wanted Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
G Warning about Deltronic Gage Pins - The "Certification of Accuracy" document General Measurement Device and Calibration Topics 13
A Gage type 1 study on CMM Capability, Accuracy and Stability - Processes, Machines, etc. 2
Q Gage R&R for Instant Measurement Machine Manufacturing and Related Processes 6
M Gage R&R with large inter part variance - Torque Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 7
D Do we need normal data for gage r&r studies? Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 5

Similar threads

Top Bottom