How do you specify a one sided tolerance for an MSA in Minitab v 16

B

Black arrow

#1
Hi,

How do you specify one sided tolerance in Minitab v 16. Is about a MSA study.

Thanks!
 
Elsmar Forum Sponsor

Bill McNeese

Involved In Discussions
#2
Re: MSA-One sided tolerance in Minitab

In Minitab 15, it is under the Options button when you are doing the crossed Gage R&R study. You can specifiy either the USL, LSL or USL-LSL. At least one spec must be entered. I would assume it is similar in Minitab 16.
 
B

Black arrow

#3
Re: MSA-One sided tolerance in Minitab

Hi again,

I made a test and % Tolerance reduced by 6% when i just entered upper limit and leaved lower limit blanked.

If i enter upper and lower limit with values i will increase the % Tolerance again.

Could this by right way to handle one sided tolerance like cylindricity?
 
B

Black arrow

#5
Re: MSA-One sided tolerance in Minitab

Hi Miner,

Thanks for the information but i still don't know how i enter the values in a correct way in "options" in Minitab when it is about one sided tolerance? Is it correct to do as i described earlier?
 

Miner

Forum Moderator
Staff member
Admin
#6
Cylindricity would be considered a maximum specification. Enter the specification for the upper spec limit only then run your analysis.
 
Thread starter Similar threads Forum Replies Date
M ECG lead leakage currents - How to specify ECG leads during electrical safety testing IEC 60601 - Medical Electrical Equipment Safety Standards Series 5
D Drawing (print) does not specify restrained or free state Inspection, Prints (Drawings), Testing, Sampling and Related Topics 2
L How do you specify your receiving inspection parameters? Misc. Quality Assurance and Business Systems Related Topics 2
somashekar How do you specify color tolerance ... Manufacturing and Related Processes 6
P How to specify criteria for TECN (Temporary Engineering Change Notice) Document Control Systems, Procedures, Forms and Templates 3
B How to specify a calibration accuracy? General Measurement Device and Calibration Topics 12
I Guidelines that specify the frequency of ETO Sterilizer Re-Validation ISO 13485:2016 - Medical Device Quality Management Systems 5
E How to specify Paint or Plastic Color - Pantone or Manufacturer Specification? Manufacturing and Related Processes 15
J Change Management System - Does ISO 9001 specify you need a process flow? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 11
S Cleaning Protocol Validation - Do we also have to specify the level of cleaning? ISO 13485:2016 - Medical Device Quality Management Systems 7
L Material Safety Data Sheet - MSDS should specify how to make the material innocuous Miscellaneous Environmental Standards and EMS Related Discussions 10
G AS9100 4.9 Process Control - Specify process documents and their revision levels AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 6
T ISO 17025 Method Verification - One sided “F” test or two sided “F” test ISO 17025 related Discussions 1
B One sided tolerance Cylindricity - Result from MSA Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 10
B Does anyone have links to one sided CPK files? Excel .xls Spreadsheet Templates and Tools 2
P One sided confidence interval for probability plot in Minitab Using Minitab Software 1
U One Sided Tolerance Distribution(s) Capability, Accuracy and Stability - Processes, Machines, etc. 5
M FDA Submission Printing Format - Is double sided printing allowed? Other US Medical Device Regulations 5
A Converting 1-Sided Design Tolerance to a Bilateral Tolerance Statistical Analysis Tools, Techniques and SPC 8
J Type 1 GRR (Gage R&R) on a One Sided Specification Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 6
optomist1 Nested Gage R & R One Operator One Sided Spec Using Minitab Software 5
optomist1 MSA Gage R&R - Destructive Test with One Sided Specification and One Operator Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
A How to define one sided spec or two sided spec for 70 +0.3 Capability, Accuracy and Stability - Processes, Machines, etc. 15
C Gauge R&R %Tolerance Template for One-sided Tolerance - Wire Pull Tester Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
J Process Control/Standard Deviation Question on a One Sided Specification Capability, Accuracy and Stability - Processes, Machines, etc. 6
L %GRR/TV or /TW for GRR of One Sided Specification - Gage R&R Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 6
Miner Intro to MSA of Continuous Data - Part 9: %Tolerance for One-sided Specs Imported Legacy Blogs 3
A Cp, Cpk for One Sided Specification Statistical Analysis Tools, Techniques and SPC 2
B Calculating Capability on a One-Sided Tolerance Dimension Capability, Accuracy and Stability - Processes, Machines, etc. 12
K Minitab version 15 Gage R&R and Single Sided Specification Using Minitab Software 5
S Using the results from GR&R (Gage R&R) Analysis - One sided dimension Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 25
T Double-sided (USL, LSL) Variables sampling plan Z1.9 - Use in Excel spreadsheet? Inspection, Prints (Drawings), Testing, Sampling and Related Topics 2
J Control limits for one sided control charts using WECO rules Statistical Analysis Tools, Techniques and SPC 5
ScottK Measuring Capability on a One Sided Variable (Surface Finish) Capability, Accuracy and Stability - Processes, Machines, etc. 17
T One sided F-test in Minitab Using Minitab Software 5
S How to perform a Two One Sided T (TOST) Test in Minitab Using Minitab Software 8
S If a process has a one sided specification, what can I calculate for? Six Sigma 2
L One sided Control Chart with only UCL or LCL Statistical Analysis Tools, Techniques and SPC 2
D Ppk of non-normal bounded proccess, one sided specification Capability, Accuracy and Stability - Processes, Machines, etc. 3
Y Noise Tester GR&R (Gage R&R) study on one sided specification Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 9
D One-Sided Tolerance Gage R&R Analysis Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 1
T Calcuating a one sided (LSL) Cpk for Proccess Capability Capability, Accuracy and Stability - Processes, Machines, etc. 17
F Ppk/Cpk value with 1-sided specification - Only given a lower specification Statistical Analysis Tools, Techniques and SPC 1
G Destructive test, gage R&R with one sided tolerance Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
G How to complete gage R&R when you have only a single sided tolerance Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 14
X Calculating Tolerance with One Sided Limits - Need a Form to Calculate Statistical Analysis Tools, Techniques and SPC 6
G Setting Control Limits - SPC for one sided dimensions Statistical Analysis Tools, Techniques and SPC 2
A Precision/Tolerance Ratio for 1-sided Specification - How to Compute Inspection, Prints (Drawings), Testing, Sampling and Related Topics 3
K SPC for One-sided Specification - Setting the Lower Control Limit Statistical Analysis Tools, Techniques and SPC 4
G SPC control for one-sided specification Statistical Analysis Tools, Techniques and SPC 3

Similar threads

Top Bottom