How to Measure the Minor Diameter of Internal Threads

L

leetimothyj

#1
We are purchasing slotted hex nuts (9/16"-18, class 2B) for a load supporting application for overhead material handling equipment. We have been measuring the nuts with both a thread pitch (go / no-go) gage and a cylindrical plug gage to measure the maximum minor diameter. According to ANSI/ASME B1.1, the minor diameter for this internal thread can be a maximum of 0.515". The nuts conform to the thread pitch gage, but we are rejecting them based on an oversize condition on the minor diameter, e.g. 0.520" - 0.525". Our supplier says that this is not a valid measurement, that you only use the pitch diameter. I am not that well versed in fasteners, but my thought is that the less material (i.e., the larger the minor diameter), the less support and greater potential for the nut to strip out. If this dimension is not 'valid' then what determines the minimum amount of thread surface? Thanks in advance for your input and any direction to an 'expert' source (not that you aren't experts!) I did once hear the definition of an expert as "ex" = has been + "spurt" = a drip under pressure. I am an ex-spurt in many fields!:thanx:
 
Elsmar Forum Sponsor

Jim Wynne

Staff member
Admin
#2
leetimothyj said:
We are purchasing slotted hex nuts (9/16"-18, class 2B) for a load supporting application for overhead material handling equipment. We have been measuring the nuts with both a thread pitch (go / no-go) gage and a cylindrical plug gage to measure the maximum minor diameter. According to ANSI/ASME B1.1, the minor diameter for this internal thread can be a maximum of 0.515". The nuts conform to the thread pitch gage, but we are rejecting them based on an oversize condition on the minor diameter, e.g. 0.520" - 0.525". Our supplier says that this is not a valid measurement, that you only use the pitch diameter. I am not that well versed in fasteners, but my thought is that the less material (i.e., the larger the minor diameter), the less support and greater potential for the nut to strip out. If this dimension is not 'valid' then what determines the minimum amount of thread surface? Thanks in advance for your input and any direction to an 'expert' source (not that you aren't experts!) I did once hear the definition of an expert as "ex" = has been + "spurt" = a drip under pressure. I am an ex-spurt in many fields!:thanx:
Your purchase order should specify the standard you expect the nuts to meet. If the supplier accepts the order and the nuts don't meet the standard, you're within your rights to reject them, regardless of the particular reason. You shouldn't specify "Class 2B" without also specifying "UNC" or "UNF" (e.g.), and the national standard. Whether or not the supplier has a case depends on what you ordered from them.
 
L

leetimothyj

#3
Clarification; The nut was specified as "9/16"-18, UNF, 2B" and stated standard as ANSI B18.2.2. Thanks, Tim
 

Jim Wynne

Staff member
Admin
#4
leetimothyj said:
Clarification; The nut was specified as "9/16"-18, UNF, 2B" and stated standard as ANSI B18.2.2. Thanks, Tim
You're welcome. If you specified the standard, you're on steady ground.
 

Wayne

Gage Crib Worldwide
#5
Proper Thread Measurement

leetimothyj said:
We are purchasing slotted hex nuts (9/16"-18 UNF-2B).... We have been measuring the nuts with both a thread pitch (go/nogo) gage and a cylindrical plug gage to measure the maximum minor diameter.... Our supplier says that this is not a valid measurement, that you only use the pitch diameter....
I sell thread plug gages for a living. Your supplier is wrong. The thread plug gage does not fully check the thread. The GO gage checks the thread maximum material condition of the pitch diameter and the major diameter but does no measurement of the minor diameter. The NOGO gage only checks to see if the pitch diameter has not been machined too large. It does not measure either the major or minor diameters. To fully gauge an internal thread, a Minor Diameter GO/NOGO Plain Pin Gage must be used.

BTW: For an external thread, the same is true of the major diameter. It must be measured by a tool other than the thread ring gage.
 
G

Gordon Clarke

#6
Re: Proper Thread Measurement

This isn't exactly a "quick" reply as I've only recently found this forum. Still, better late than never :)
I agree with Wayne 100% in that gauges don't "measure" - they inspect for right or wrong. By measuring you always know where you are with relation to the tolerance.

I have invented and patented (and sell) a method for (among other things) measuring thread pitch diameter and can in fact also measure internal threads from M6 - 1/4".
I have on two occasions supplied thread measurement inserts for measuring diameter D on an internal thread. It is true that the tolerance for this is the only diameter (major diameter on an internal thread) that doesn't have a specified tolerance and is only given as "min." This applies to both Unified Inch Screw Threads (UN) and Metric Screw Threads. Of course this doesn't mean that it can't or musn't be measured.

My personal opinion on making the "perfect" thread is to use a combination of solid thread plug and7or ring gauges and pitch diameter measurement. A good thread is in the middle of the pitch diameter tolerance. Measurement also reveals how much of the tolerance is being used and whether or not the process is being controlled. A gauge doesn't reveal this. Inspection by solid gauges usually requires a much larger sample size than measurement. Another advantage is that when setting a machine up, if the thread cutting tool is set for the middle of the tolerance process control can be reduced and focus moved to viual inpection of the cutting tool. Keeping away from the tolerance limits also means less wear on the solid gauge.

Another Rule of Thumb for UN and Metric threads is that, if the pitch diameter tolerance for an external screw thread = 1, then the pitch diameter tolerance for an internal thread is 1.3
The pitch diameter tolerance for threads is invariably the smallest tolerance on the three diameters. If the cutting tool isn't damaged or worn then measuring the pitch diameter is usually enough to ensure that the overall profile is OK and the thread within tolerance.

I have also made a simple observation with UN threads:
if tolerance 2A is known then all other tolerances (1A, 3A, !B, 2B and 3B) follow this one.

If anyone has questions then I'd be happy to answer - assuming I can :)

Gordon
 
Last edited by a moderator:
M

MACIEK

#7
Re: Measuring minor diameter of internal threads - How To?

Hello.
Does any one have an idea where i can obtain threaded ring gauge minor diameter tolerances?:thanks:
 
G

Gordon Clarke

#8
Re: Measuring minor diameter of internal threads - How To?

Hello.
Does any one have an idea where i can obtain threaded ring gauge minor diameter tolerances?:thanks:
It will depend on the type of thread you want this information for. There isn't a universal answer for "thread ring gauges" I notice by your spelling of gauge that you're probably not from the USA ;) If it's a metric thread then ISO 1502 will probably be your best bet.
If you give more information i'm certain you can get the correct answer. Wayne (gageguy) is certain to know the answer if he reads this :D I can probably help too, but only if I get all the information you have on the thread type and size.
 

Wayne

Gage Crib Worldwide
#9
Re: Measuring minor diameter of internal threads - How To?

Does any one have an idea where I can obtain threaded ring gauge minor diameter tolerances?:thanks:
The best place is from the standard. Which standard depends on which type of thread you are working with and which country you are working in.

Type of thread could be: Unified; Metric; Whitworth; NPT; ANPT; NPTF; ACME; Stub ACME; Buttress; Tr; G-Series; R-Series; Pg; Rd; Various forms of API, and then there are proprietary threads. The minor diameter requirements may vary for each type.

Which country are you working in. In USA we use ANSI or ASME standards. In EC they use ISO standards. Of course the choice of standard may be decided by where the product is being shipped to, or by decree of design engineer regardless of country affiliation.The minor diameter requirements may vary for each standard convention.

There are multiple software programs which give you a good selection of standard types of thread to choose from. I am a seller of thread measurement tools and I can sell you: Thread Disc; ThreadTech or STETFS screw thread engineering software. I use ThreadTech most and there is a 10-day Free Trial available on my website. Stefanhg also has a shareware software available. For more detailed discussion on software read: Thread Gage Calibration Software to look up requireds/specs for thread gages.

Of course before you go out and buy software you should be sure to identify the answers to the first two questions.

Now for the most simple way to find the minor diameters of your ring gages: Look on the original manufacturer's Long Form Certification that came with the gages. The minor diameter with its tolerance will be listed there. If you have not been ordering Long Form Certifications with your gages, it may be a good time to start. The standard free certification usually does not list this type of data.

I hope this helps you in your search.
 
Last edited by a moderator:
G

Gordon Clarke

#10
Re: Measuring minor diameter of internal threads - How To?

We are purchasing slotted hex nuts (9/16"-18, class 2B) for a load supporting application for overhead material handling equipment. We have been measuring the nuts with both a thread pitch (go / no-go) gage and a cylindrical plug gage to measure the maximum minor diameter. According to ANSI/ASME B1.1, the minor diameter for this internal thread can be a maximum of 0.515". The nuts conform to the thread pitch gage, but we are rejecting them based on an oversize condition on the minor diameter, e.g. 0.520" - 0.525". Our supplier says that this is not a valid measurement, that you only use the pitch diameter. I am not that well versed in fasteners, but my thought is that the less material (i.e., the larger the minor diameter), the less support and greater potential for the nut to strip out. If this dimension is not 'valid' then what determines the minimum amount of thread surface?
This is probably too late to be of help to you but it might help anyone else from getting into a similar predicament.

The correct specification for your thread would be 9/16-18UNF-2B

The nut tolerances are then:

Minor diameter min. 0.502 max. 0.515
Pitch diameter min. 0.5264 max. 0.5323
Major diameter 0.5625

This (and much more) can be found in the standard ASME B1.1

If any of these diameters are not within the tolerance then they can be rejected – regardless of what the thread plug gage “says”. A thread plug gage will not register if the minor diameter is too large if the pitch diameter is OK. I’ve found the easiest way to measure minor diameter on an internal thread is by using a digital caliper. It’s easy to spot potential faulty nuts, as the “bottom” of the thread (minor diameter) will have larger than normal “flats”.

Personally, I’d find another supplier simply because of the BS answers he gave to your legitimate complaint. His attitude to his products is a disaster waiting to happen.
 
Thread starter Similar threads Forum Replies Date
C First Article Inspections - 'how to measure' General Measurement Device and Calibration Topics 11
lanley liao Question regarding the calibration of monitoring and measure equipment. Oil and Gas Industry Standards and Regulations 0
J Should a Class 1 medical device with an option to measure body weight be considered Class 1m? EU Medical Device Regulations 0
M Gage R&R and right way to measure Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 16
P How to measure DPPM in Chemical batch manufacturing Quality Tools, Improvement and Analysis 1
silentmonkey How to measure severity if my product is designed for emergency use and failure would result in death? ISO 14971 - Medical Device Risk Management 9
A Looking for a third party to calibrate our measure equipment - South Carolina General Measurement Device and Calibration Topics 6
J Validity / outcomes measure for custom made medical device ISO 13485:2016 - Medical Device Quality Management Systems 2
D Performance specification as a Risk Control Measure, EN 14971 ISO 14971 - Medical Device Risk Management 7
J KPIs or Metrics to Measure a New Complaint Handling Process 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 9
D Torque fractional unit of measure; cN-m or N-cm? General Measurement Device and Calibration Topics 2
qualprod ISO 9001 5.1.1 - How to measure System effectiveness ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 4
J How to measure a Critical Characteristic that is a Basic Dimension Misc. Quality Assurance and Business Systems Related Topics 6
I Can we use pin gauges to measure an accurate Cpk ? Capability, Accuracy and Stability - Processes, Machines, etc. 9
qualprod Best criteria to measure Corrective Action effectiveness - Poor Maintenance ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 10
1 How to measure straightness on a HEX Long Bar Manufacturing and Related Processes 7
Ron Rompen Measurement Method Challenge - Measure feature #91 Inspection, Prints (Drawings), Testing, Sampling and Related Topics 9
G Measure 3 times, for calibration report? Customer Owned Reference Standard General Measurement Device and Calibration Topics 4
M Informational The ANSM decides, as a precautionary measure, to withdraw from the market macrotextured breast implants and breast implants with polyurethane-coated s Medical Device and FDA Regulations and Standards News 0
M Informational Health Canada advises Allergan of its intent to suspend its licences for Biocell breast implants as a precautionary measure Medical Device and FDA Regulations and Standards News 0
U SI 13 - Not Every Process Requires an Efficiency Measure IATF 16949 - Automotive Quality Systems Standard 1
P NPR Metric - What if Customer has relaxed measure? TL 9000 Telecommunications Standard and QuEST 1
T Tape Measure, the right device for 2 or 3 decimals accuracy on prints General Measurement Device and Calibration Topics 8
M How do we document and measure a service we do not provide? IATF 16949 - Automotive Quality Systems Standard 1
M For a Type 1 Gage R&R I want to use 1 unit and measure it 30 times Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 5
M How to Measure Paper considering Variation and Humidity General Measurement Device and Calibration Topics 10
rob73 Advice/recommendations for equipment to measure a soft pvc tube - Optical Measuring? General Measurement Device and Calibration Topics 4
R Height gauge to measure short hard to access heights General Measurement Device and Calibration Topics 3
D Proper Tool to Measure Wall Thickness (ISO 3611 - Micrometers) Manufacturing and Related Processes 7
S Quality Measure for Engineering Services Misc. Quality Assurance and Business Systems Related Topics 1
A What are methods and tools to measure Workload analysis ? Human Factors and Ergonomics in Engineering 1
M How do I measure variation in my process ? Capability, Accuracy and Stability - Processes, Machines, etc. 3
J How to measure process quality? Is DPPM the correct metric? Capability, Accuracy and Stability - Processes, Machines, etc. 5
M Micrometer Anvil Placement to measure the diameter of Steel Wires Measurement Uncertainty (MU) 6
S Where to Get SPC Training to Measure our Processes? Training - Internal, External, Online and Distance Learning 12
M A question on Measurement System Analysis - Stability to measure got Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
Jim Wynne Measure Twice, Cut Once: The French Railroad Snafu World News 18
S Measure water activity for fresh raw chicken meat and giblets Food Safety - ISO 22000, HACCP (21 CFR 120) 1
O Metrology Devices to Measure the Basic Dimensions of Plastic Specimens General Measurement Device and Calibration Topics 6
L How to Measure Paint Thickness for an Enclosure Manufacturing and Related Processes 5
C Chamfer Measurements - Do you measure the height and width or the hypotenuse? Manufacturing and Related Processes 15
R Repeatability in MSA - Is repeatability a measure of Location Error Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
E How can I measure three true positions? GD&T basic question General Measurement Device and Calibration Topics 5
V How to use a Calibration Certificate in Uncertainty Calculation for a Test Measure Measurement Uncertainty (MU) 13
R How do companies measure QC Productivity? Quality Manager and Management Related Issues 3
V How to measure radius without radius gages APQP and PPAP 4
A Device to measure "Straightness & Deformation" of a metal that's under water Manufacturing and Related Processes 4
M How to measure effectiveness and efficiency of the established QMS as Auditors ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 14
F Specification for how to measure lengths of hose assemblies Various Other Specifications, Standards, and related Requirements 1
P MSA requirements for Systems that Measure Process Parameters Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3

Similar threads

Top Bottom