Leak Tester Gage R&R Sheet

F

Flawed

#1
Morning all,

We have two leak tester units on line testing the leak rate of a part that is going into an engine.

The customer is asking for Gage R&R's which we have done. And the results are pretty good to be fair.

Yesterday he rocked up with a PDF of a sheet, that he got from another supplier and he was asking if we could do the same testing. It involves testing the same part 10 times and then using the micro calibrator to test again introducing a leak at -20% and +20% of the spec. and at the end of all this, it shows if it is capable or not.

We havent seen anything like this sheet before which I have attached.

Does anybody know of a sheet like this in excel that will keep our customer happy?
 

Attachments

Elsmar Forum Sponsor
Thread starter Similar threads Forum Replies Date
S Capability or Gage R&R Study for Leak Tester? Reliability Analysis - Predictions, Testing and Standards 15
O Capability or Gage R&R Study for Leak Tester Reliability Analysis - Predictions, Testing and Standards 11
T Gage Repeatability for an Automated Leak Tester Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 10
B Validation of a Pressure Decay Leak Tester for a Medical Device Design and Development of Products and Processes 2
G Leak Tester Calibration - Sentinal C-20 controller with a calibrated orifice General Measurement Device and Calibration Topics 1
G Leak Test - Building a master pump to calibrate pump tester Inspection, Prints (Drawings), Testing, Sampling and Related Topics 4
R Calibrating Leak Testers - Old fashioned water tank type tester General Measurement Device and Calibration Topics 2
N MSA Study for a Leak Testing Device Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 6
M Proper ISO standard for Pressure Testing and Leak Rates Inspection, Prints (Drawings), Testing, Sampling and Related Topics 6
H Validating Nondestructive leak testing machine Qualification and Validation (including 21 CFR Part 11) 3
triathlonx13 Leak test correlation - Bubble to Air Reliability Analysis - Predictions, Testing and Standards 8
GURU SDI Leak Testing - O-ring installation in the groove of Bore ID Problem Solving, Root Cause Fault and Failure Analysis 4
L Environmental Gas Leak Detection Equipment Recomendations Miscellaneous Environmental Standards and EMS Related Discussions 2
T Would a Leak be a Failure Mode on a Design FMEA? Design and Development of Products and Processes 2
GURU SDI Measurement - Pressure Drop vs. Leak Rate Inspection, Prints (Drawings), Testing, Sampling and Related Topics 8
S Destructive Attribute MSA for Simple Water Leak Check in Trailers Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 5
somashekar Why does a tap leak... Funny Stuff - Jokes and Humour 2
Claes Gefvenberg Massive gas leak off Scotland World News 12
H Determining Calibration Tolerance for new Leak and Occlusion Equipment Measurement Uncertainty (MU) 2
N Tyvek Pouch Seal - Pressure needed to conduct Vacuum Seal Leak test? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 2
V For an MDI, is leak-test a stability parameter ? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 2
S Zyglo Fluorescent Dye for Leak Testing - Sloooooow acting - Seeking advice Reliability Analysis - Predictions, Testing and Standards 4
R Sample Size for P Chart - 100% Leak Test for Condensor Inspection, Prints (Drawings), Testing, Sampling and Related Topics 5
R Seal Packaging - Burst and Leak Specifications for a Foil Seal applied to a PTFE well Manufacturing and Related Processes 4
W Oven Leak Test Method - Integrity of the chamber to hold gas Qualification and Validation (including 21 CFR Part 11) 3
D Leak Test Method for Balloon Catheters EU Medical Device Regulations 2
B MSA (Gage R&R) vs. Capability Cpk Study - Helium Leak Check Station Statistical Analysis Tools, Techniques and SPC 2
D Halogen Leak Detector - Calibration source needed General Measurement Device and Calibration Topics 1
ScottK Oxygen Cleaning and Surfactants used for leak detection Various Other Specifications, Standards, and related Requirements 1
T Calibration of vacuum type leak detectors manufactured by Vacuum Technology Inc General Measurement Device and Calibration Topics 5
H GR&R (Gage R&R) on leak test equipment is there a deviation requirment? Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 5
C Master Validation Frequency in production - Absence of leak, thread presence, etc. Reliability Analysis - Predictions, Testing and Standards 4
W Leak Detection - Oven Seals General Measurement Device and Calibration Topics 1
M Developing a Leak Test - Housing part for an automotive customer Various Other Specifications, Standards, and related Requirements 7
S Shore A hardness Tester Acceptance Criteria Standard Elsmar Cove Forum Suggestions, Complaints, Problems and Bug Reports 2
B Photovoltaic Tester Calibration General Measurement Device and Calibration Topics 0
P Test Method Validation for Tensile Strength Tester Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 0
A Tubing Clog Tester - Convert from Air Bubble to Flow Rate Reliability Analysis - Predictions, Testing and Standards 1
S GR&R for Hardness Tester and Arc Spark Spectrometer Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 15
alonFAI Gauge R&R for a Peel Tester (tensile tester) Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 11
S GRR (Gage Repeatability and Reproducibility) for Material Strength Tester Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 6
S MSA (measurement system analysis) on Flammability tester? Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
D Wire/Conductor Elongation Tester Verification General Measurement Device and Calibration Topics 2
M Valve Tester GR&R Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
A How to Calibrate Laser Beam Tester & Radiation Monitor General Measurement Device and Calibration Topics 3
W Profilometer Surface Roughness Tester Issue - Ball Bearings ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 7
L Calibration of ESD Wrist Strap Tester General Measurement Device and Calibration Topics 14
S GR&R for an "R" value instrument installed on my 10K Horizontal Tester Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 5
C How to Calibrate a Viscosity Tester General Measurement Device and Calibration Topics 3
L Building your own Leakage Current Tester IEC60990 Other US Medical Device Regulations 4

Similar threads

Top Bottom