Mechanical Drawing Aprovals

M

mibusha

#1
#1
Somewhere I have seen it written that before release mech prints must be signed by the originator, checked by a second person, and then approved (not necessarily by either of the first two people). It is in my procedures but now I can't find where it calls for it in the standards. (ISO 9001, QS 9000, TE). Did I just make it up?

Michael
 
Highly Rated Gage Tracking - Learn More
Elsmar Forum Sponsor
S

Sam

#2
#2
You might check the ANSI drafting standards. I seem to remember something there about sign-off responsibility.
It's a long reach, but you can get there from QS-9000.
 
You must log in or register to reply here.
Thread starter Similar threads Forum Replies Date
alonFAI Mechanical Drawing Version Change Document Control Systems, Procedures, Forms and Templates 8
N FDA mechanical bench testing Manufacturing and Related Processes 5
Strange Juan HP 85054B Standard Mechanical Calibration Kit Calibration Procedure General Measurement Device and Calibration Topics 1
G Pricing Structure for Physical Mechanical Testing of Labs Manufacturing and Related Processes 1
S Mechanical Test Under FDA Freedom of Information Act Medical Device and FDA Regulations and Standards News 5
J Defining staff competence - Small mechanical workshop Occupational Health & Safety Management Standards 20
M Device mounted at IV pole - what about mechanical stability testing? IEC 60601 - Medical Electrical Equipment Safety Standards Series 2
J Mechanical inspection techniques of close tolerance parts Inspection, Prints (Drawings), Testing, Sampling and Related Topics 4
B IEC 60601 - Creepage Distance - Relay that acts as a means of physical mechanical protection Process Maps, Process Mapping and Turtle Diagrams 0
J GLP accreditation for mechanical tests of medical device? Other Medical Device and Orthopedic Related Topics 1
A Moving and positioning of patient - Mechanical hazard IEC 60601 - Medical Electrical Equipment Safety Standards Series 18
shimonv Design input/output traceability for mechanical parts ISO 13485:2016 - Medical Device Quality Management Systems 31
R Essential Performance of Mechanical Device? IEC 60601 - Medical Electrical Equipment Safety Standards Series 6
X Heat Treat - Verifying mechanical properties on heat treated material per the ASTM Manufacturing and Related Processes 6
J Mechanical Press Machine Foundation Requirements and Recomendations Manufacturing and Related Processes 2
G Senior Project for BS Mechanical Engineering Student Career and Occupation Discussions 4
M Mechanical Testing for Orthopaedic Implants for CE Marking EU Medical Device Regulations 2
A Auditor's certificate for newly employed graduate? (Mechanical Engineer) Professional Certifications and Degrees 1
R Standard for Reliability/Performance Test on a Electro Mechanical Device IEC 60601 - Medical Electrical Equipment Safety Standards Series 1
T Measurement of uncertainty for standard mechanical properties General Measurement Device and Calibration Topics 1
N Need Calibration Service for Mechanical Tester - Zwick Roell General Measurement Device and Calibration Topics 1
D Contract Manufacturer & Mechanical Assembly Supplier Warranty Liability ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 1
J Mechanical Tubing Mill Tolerance Reference Manufacturing and Related Processes 5
S Mechanical/Electrical Forces Gage Calibration Methods Calibration and Metrology Software and Hardware 1
W Seeking a Freelance Mechanical Inspector - Source Inspection in Bangalore, India AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 1
S Medical Device Mechanical Test Method Validation Design and Development of Products and Processes 8
Uriel Alejandro Trouble with a Mechanical Design Technical Verification Check List AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 2
C Inexperienced Mechanical Inspectors and FAI's (First Article Inspection) Inspection, Prints (Drawings), Testing, Sampling and Related Topics 1
M Mechanical Auto Repair Shop requires ISO 9001 Certification ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 11
J Fastener Manufacturing Research - Mechanical and Engineering Theories Manufacturing and Related Processes 3
J Define Energy Used/Delivered - Applicable to Electrical or Mechanical Power or both? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 1
Q Failure Analysis Procedure for Electro-Mechanical Devices 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 1
A HSE Regulations and Legislation for Design of Mechanical Wind Turbine Components Miscellaneous Environmental Standards and EMS Related Discussions 4
P Dimensional Mechanical Inspection only as a Service - ISO17025 or ISO17020 ISO 17025 related Discussions 5
somashekar Insight about Air Changes per hour (ACH) in Mechanical Ventillation Occupational Health & Safety Management Standards 2
C Analyzing Attribute Data - Mechanical Pull Testing of Joint Statistical Analysis Tools, Techniques and SPC 15
J FAA Requirements for Design and Manufacturers of Engine Turbine Mechanical Components Federal Aviation Administration (FAA) Standards and Requirements 2
D Material Handling, Storage & Preservation Procedure for Aerospace Mechanical Parts AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 2
R Inspection Humidity Control - Range for Mechanical Inspection Inspection, Prints (Drawings), Testing, Sampling and Related Topics 1
V Mechanical Testing Lab - PT vs. QC questions General Measurement Device and Calibration Topics 4
P Calibration Standard - Rules of Calibration for Mechanical Comparators General Measurement Device and Calibration Topics 3
N Help please - Mechanical Latch Design Principles? Design and Development of Products and Processes 2
Q REACH Declaration requirements for Mechanical Components RoHS, REACH, ELV, IMDS and Restricted Substances 6
V PPAP for electronics - What do we have to require for PCB compare to mechanical parts APQP and PPAP 4
V Letter of Guarantee - EN 12546-3 (Mechanical & Physical testing on an ice pack) Inspection, Prints (Drawings), Testing, Sampling and Related Topics 7
R BOMs & Test Procedures - Electronic and electro-mechanical systems Document Control Systems, Procedures, Forms and Templates 4
M Mechanical Maintenance Procedures for Oil & Gas wanted Document Control Systems, Procedures, Forms and Templates 4
ScottK National Pipe Straight Mechanical (NPSM) Specification? Various Other Specifications, Standards, and related Requirements 6
A How to Search for Jobs Abroad - Mechanical Engineering Field Career and Occupation Discussions 3
D Can an Electrical Design Engineer audit the work of a Mechanical Design Engineer? Design and Development of Products and Processes 6

Similar threads

Top Bottom