R&R difference between QS9000 and ASTM

F

Fanjun

#1
R&R difference between QS9000 and ASTM


I learned MSA a month ago. I found that the Reproducibility is smaller than the Repeatability in the calculation of Gage R&R. But in all standards of analytical method such as ASTM and ISO standards, Reproducibility is always bigger than Repeatability. How to explain it?
 
Elsmar Forum Sponsor
D

Don Winton

#2
Fanjun,

Reproducibility is always bigger than Repeatability.
This should not be the case. Each should be based on the data collected and the respective variations. Perhaps a re-check of the references is in order. In some cases, variation across operators will be greater than variation across trials and vise versa.

Maybe someone else more knowledgeable in the mechanics of the MSA manual methodology could shed some light on this, but I believe the statistics of ANOVA (on which the R&R is based) would preclude this from happening.

Regards,
Don
 
F

Fanjun

#3
I have some ASTM Standard Test Methods on hand such as ASTM D5708-95a , ASTM D2007-93 and so on. In D5708-95a,it says the Repeatability of Vanadium is 4.0 mg/kg,the Reproducibility of it is 19 mg/kg,when the concentration is 100 mg/kg. In D2007-93,the result is Repeatability: 1.3%, Reproducibility: 7.8%.
They all show that Reproducibility is bigger than Repeatability,and my other ASTM methods show the same case.
I think you can find them somewhere and will be kindly so as to give me an explanation.
 
D

Don Winton

#4
Fanjun,

My response was to indicate this is not ALWAYS the case. I could (and will if needed) provide examples where repeatability is larger than reproducibility. The LTV manual has some of this type.

Advice: Do not use examples as the condition. Variability exists just as much across operators as across trials.

Regards,
Don
 
B

Batman

#5
Could it be that Fanjun is reading a particular test method, that has been analysed before? I could state that on a particular laser micrometer in my lab, on a particular shaft diameter, that the Equipment variation [Repeatability] is 11.1%, the Appraiser variation [Reproduceability]is 4.5% for a combined 12.03% (real example.) This test would of course vary the next time, but in general if I was writing a specification for the test method here I could state the above percentages?
 
D

Don Winton

#6
Could it be that Fanjun is reading a particular test method, that has been analysed before?
I think that is the case. Your example is is a good explanation of what I was trying to express.

As I stated, I could also provide others, but I believe your points are well taken and should provide enough explanation.

Regards,
Don
 
Thread starter Similar threads Forum Replies Date
Marc What is the difference between ISO9001 & QS9000? QS-9000 - American Automotive Manufacturers Standard 2
T Difference between a subcontractor and a supplier ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 14
H Difference between Stainless Steel 316 ASTM F899 and ASTM A276 Other Medical Device Related Standards 1
A Exact terms for a plating failure and difference between rejection rate and failure rate Manufacturing and Related Processes 9
M Difference between MSA and MSE? General Measurement Device and Calibration Topics 1
G What is the difference between discrete and continuous variables? Problem Solving, Root Cause Fault and Failure Analysis 5
JoCam Difference between Approval and Registration - ISO 13485:2016 ISO 13485:2016 - Medical Device Quality Management Systems 2
S Difference between EU-MDR Annex IX and the Annex-combo X&XI EU Medical Device Regulations 2
T ISO 17025:2017 Clause 4.2.2 - The difference between "be notified" and "be informed" ISO 17025 related Discussions 4
Jimmy123 What is the difference between Error Proofing and Controls? ISO/IATF 16949 - Control Plans FMEA and Control Plans 16
C IEC 60601-1-8, difference between table 4 and annex D IEC 60601 - Medical Electrical Equipment Safety Standards Series 2
A What is the difference between Basic UDI-DI and UDI-DI? EU Medical Device Regulations 5
Q What is the difference between AS9100D 9.3.2.f and 9.3.3.a AS9100, IAQG 9100, Nadcap and related Aerospace Standards and Requirements 7
M Aluminum - What is the difference between 6061-T6 and 6061-T651 (both per ASTM B211)? Manufacturing and Related Processes 4
P What is the exact difference between Risk and Opportunity in context of ISO 27001? IEC 27001 - Information Security Management Systems (ISMS) 7
S Difference between Surface Finish (Ra) and Flatness (GD&T) Inspection, Prints (Drawings), Testing, Sampling and Related Topics 6
O Air Flow - Which is the operational difference between LAF (vertical and horizontal) and RLAF? Manufacturing and Related Processes 2
S What the difference is between Stub Acme & Acme thread? Oil and Gas Industry Standards and Regulations 1
S DO 178B - What is the difference between review and verification? Federal Aviation Administration (FAA) Standards and Requirements 1
T The difference between SOP and Kaizen Standardization Lean in Manufacturing and Service Industries 2
K Difference between intended purpose and intended use of the device EU Medical Device Regulations 9
Q What is the difference between normal and licensed internal auditor? VDA Standards - Germany's Automotive Standards 9
J What is the difference between Process Variation and Tolerance? Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
O Difference Between PFMEA & Control Plan FMEA and Control Plans 3
S Difference between an Advisory Notice (ISO 13485) and a Field Safety Notice? ISO 13485:2016 - Medical Device Quality Management Systems 3
T Difference between "data analysis" and "management review" ISO 13485:2016 - Medical Device Quality Management Systems 4
Q What is the difference between 7.4.1 (2008) and 8.4.1 (2015)? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 6
D Difference between uncertainty and expanded uncertainty of measurement General Measurement Device and Calibration Topics 1
S EASA Part 145 - The difference between non-certifying staff and Certifying staff Federal Aviation Administration (FAA) Standards and Requirements 2
S The difference between a Medical Device Accessory and Component Canada Medical Device Regulations 2
S What is the difference between a service request and a complaint? ISO 13485:2016 - Medical Device Quality Management Systems 2
I What is the difference between OOS/OOT Imported Legacy Blogs 3
A Definition Difference between Quality System Procedure and Standard Operating Procedure (SOP) Definitions, Acronyms, Abbreviations and Interpretations Listed Alphabetically 3
Q Difference between Monitor & Measurement ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 4
T QA vs. RA - The difference between QA and RA Coffee Break and Water Cooler Discussions 6
A Difference between Discrimination and Least Count IATF 16949 - Automotive Quality Systems Standard 2
K Difference between Medical Electrical Equipment and Medical Equipment System IEC 60601 - Medical Electrical Equipment Safety Standards Series 2
M Usability Standard - The difference between IEC 60601-1-6 to IEC 62336 Human Factors and Ergonomics in Engineering 1
S What is the difference between Verification and Validation of Test Reports? AS9100, IAQG 9100, Nadcap and related Aerospace Standards and Requirements 5
A Difference between ISO 9001:2015 Clauses 8.1 and 8.5.1 ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 8
M IATF 16949 Cl. 8.4.2.2 vs 8.6.5 - Is there any difference between these clauses? IATF 16949 - Automotive Quality Systems Standard 7
C What is the difference between "Overall Risk" and "Risk"? (ISO 14971) ISO 14971 - Medical Device Risk Management 10
C The difference between a Critical Dimension vs. Critical Characteristic Misc. Quality Assurance and Business Systems Related Topics 2
A ISO 9001:2015 - The difference between 6.1.1b and 6.1.1d - IMHO, d) implies b) ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 1
A Difference between requirement for 4.4.1a (inputs) and 4.4.1d (resources needed)? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 3
R The difference between Feasibility Assessment and Contract Review Contract Review Process 2
V Difference between Non-Conformance, Variance and Deviation ISO 13485:2016 - Medical Device Quality Management Systems 7
A Difference between Environmental Impact and Risk ISO 14001:2015 Specific Discussions 7
A Difference Between Complaints and Feedbacks in terms of Follow-Up Actions Needed Customer Complaints 3
M What is the difference between ISO 9000 and ISO 9001? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 2
Similar threads


















































Top Bottom