Suggestion for Gage R&R with only one limit

  • Thread starter Guy Van Hooveld
  • Start date
G

Guy Van Hooveld

#1
anybody an experience with the following problem:
how to do a GRR if you only have an upper limit (for instance there is a maximum temperature you cannot reach, but there is no lower limit).
I would think of trying to get an estimate of the capability of the process so that I can determine a kind of "virtual" lower limit...

Any suggestion or practical experience with this type of situation ?

Thanks in advance for any useful reply.
 
Elsmar Forum Sponsor
J

justncredible

#2
What will you be using to view the results? Minitab has a boundary option, and I bet the excel sheets here do as well.
 
G

Guy Van Hooveld

#3
What will you be using to view the results? Minitab has a boundary option, and I bet the excel sheets here do as well.
I will be using Minitab. I found the option... Thanks. I will experiment with it. Hope this does the job.
 
J

justncredible

#4
In minitab just leave the 0 one blank, no need to to lock it.

Now if your gage starts at 5 and has no upper limit then you would use the boundary toggle. That way nothing will be allowed below 5.
 
Thread starter Similar threads Forum Replies Date
J Gauge Suggestion: Specialty or Custom General Measurement Device and Calibration Topics 1
P Suggestion for QMS platform solution + Business process automation Software Quality Assurance 3
A Free software similar to Microsoft Project - Any suggestion? APQP and PPAP 5
C Customer Satisfaction Process - Audit "Suggestion for Improvement" General Auditing Discussions 14
M Laser Micrometer Suggestion (if any) for diameters that are +/-.0001 inch General Measurement Device and Calibration Topics 1
P Need suggestion on Software or App for Tracking Quality Plan Status Software Quality Assurance 1
D Service Owner of the e-suggestion scheme Service Industry Specific Topics 1
B Any suggestion on creating the best paper plane that can hit a target perfectly? Coffee Break and Water Cooler Discussions 2
MarilynJ6354 Definition Improvement Suggestion vs. Preventive Action - Clear Definitions and Differences Definitions, Acronyms, Abbreviations and Interpretations Listed Alphabetically 6
A SFI x PA (Suggestion for Improvement x Preventive Action) How to register them ? Preventive Action and Continuous Improvement 4
L Difference between a Preventive Action and a Suggestion System Preventive Action and Continuous Improvement 2
C Suggestion for Implementing ISO 9001 in a Start-Up Company ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 14
C How to use a PAS (Preventive Action Suggestion) Preventive Action and Continuous Improvement 5
D Managing an Employee Suggestion Program Quality Manager and Management Related Issues 4
R ISO 17025 - Suggestion for Interlaboratory Comparison Measurement ISO 17025 related Discussions 4
K Suggestion System - Advice for a Reward System to Sustain a Long Life Manufacturing and Related Processes 2
M Suggestion System - Do's & Don'ts as well as Rewards System Manufacturing and Related Processes 29
D A suggestion to my boss - What do you think and how will he react? Lean in Manufacturing and Service Industries 46
Sidney Vianna Suggestion to "green" ASQ - Option to not receive the magazine ASQ - American Society for Quality 21
M Suggestion for Quality Poster for my company Quality Campaign Training - Internal, External, Online and Distance Learning 5
Q Suggestion Program - Suggestion programs to improve our own and benchmark against Quality Tools, Improvement and Analysis 5
M Advise: Cost and suggestion of APQP planning software APQP and PPAP 2
C Employee Suggestion System - Recommendations on Implementing a Suggestion System? Misc. Quality Assurance and Business Systems Related Topics 14
B Suggestions for Suggestion Systems - CI (Continuous Improvement) Preventive Action and Continuous Improvement 24
CarolX Preventive Action (PA) - Employee Suggestion Box, Engineering Change Order? Preventive Action and Continuous Improvement 12
A Any suggestion for a Process Improvement demo Manufacturing and Related Processes 9
Geoff Cotton "Todays Active Topics" a suggestion. Coffee Break and Water Cooler Discussions 2
T Plug Gage Calibration Calibration and Metrology Software and Hardware 1
L Gage R&R TMV Acceptance Criteria Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
S MSA for attribute relation gage Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
E Zero part to part variation - Gage R&R project Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 15
M Gage R&R and right way to measure Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 16
L Gage RandR on automated equipment. IATF 16949 - Automotive Quality Systems Standard 7
B Gage calibration frequency, ISO and IATF - What are the requirements Calibration Frequency (Interval) 3
D Difference between Test Method Validation and Gage R&R Qualification and Validation (including 21 CFR Part 11) 18
R Determining Uncertainty from Gage R&R Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 1
C Correct Calibration Method for Dial Depth Gage General Measurement Device and Calibration Topics 6
C Gage Block Wringing General Measurement Device and Calibration Topics 3
B Gage R&R with NDC=1 Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 19
S Type 1 Gage R&R or something else? Reliability Analysis - Predictions, Testing and Standards 6
G Should I perform Gage R&R only at the beginning of a new project? Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 6
V Thread Plug Gage Pitch GO Diameter out of spec AQL - Acceptable Quality Level 8
G Gage R&R - Where am I going wrong? Part of a FAIR submission (Aerospace) Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
R Gage R&R Excel templates Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
K Gage R&R with more than 3 appraisers Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
Anerol C Gage R&R Template AIAG 4th Edition IATF 16949 - Automotive Quality Systems Standard 3
T Attributes SPC study - Attributive control (Go gage) Statistical Analysis Tools, Techniques and SPC 5
S Capability or Gage R&R Study for Leak Tester? Reliability Analysis - Predictions, Testing and Standards 15
N % Tolerance - Type 1 study on the gages, then a gage R&R (ANOVA) Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
M Definitive answer on Type 1 vs Type 2 vs Type 3 Gage Study Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 0

Similar threads

Top Bottom