SBS - The best value in QMS software

Surface Finish parameters - Mechanical stylus based testing of a cylindrical part

W

weekendwarrior77

#1
Hello all,
I have a question surface finish measurement methods and I will appreciate any help in this regard.
How do I determine the type of measuring technique/method to be used for a specific part/component. In other words, what are the factors to be determined/taken into account while selecting the right kind of measuring method.
Also If I use say a mechanical stylus based testing for measuring the surface finish of a cylindrical part. How does it transform to the surface finish of the entrire metallic rod. In other words, how does the 2d measurement transform to a 3d measurement.

Once again any help is appreciated.

Thanks
 
Elsmar Forum Sponsor
Thread starter Similar threads Forum Replies Date
K Surface finish (Evaluation Length) Inspection, Prints (Drawings), Testing, Sampling and Related Topics 3
Ron Rompen Surface Finish Correlation between Ra, Rz and Tp (bearing surface ratio) General Measurement Device and Calibration Topics 3
J Gear Surface Finish - Print with the word "calibrated" Manufacturing and Related Processes 2
8 Surface Finish - Callout as 8 - 16 Rq Manufacturing and Related Processes 1
GoKats78 Callout on Surface Finish General Measurement Device and Calibration Topics 11
S Difference between Surface Finish (Ra) and Flatness (GD&T) Inspection, Prints (Drawings), Testing, Sampling and Related Topics 6
Proud Liberal Surface finish measurement (roughness) - Rz under the ISO standard vs ANSI standard Inspection, Prints (Drawings), Testing, Sampling and Related Topics 0
Proud Liberal Measuring axial and radial surface finish (16 Rz) on a broached internal radius Inspection, Prints (Drawings), Testing, Sampling and Related Topics 1
B Surface Finish Equipment MSA (Measurement System Analysis) Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 5
kedarg6500 Surface Finish Measurement Methods Inspection, Prints (Drawings), Testing, Sampling and Related Topics 13
P Surface Finish measurement for machined (finished) component/part Inspection, Prints (Drawings), Testing, Sampling and Related Topics 2
J Definition Standards for Dimensions and Surface Finish on a Rod Definitions, Acronyms, Abbreviations and Interpretations Listed Alphabetically 11
A Is it mandatory to have a profilometer to inspect >16 surface finish? General Measurement Device and Calibration Topics 8
T Interpretation of Surface Finish Specification Manufacturing and Related Processes 2
D Surface Finish Inspection Company (Laboratory) (Detroit area) needed Manufacturing and Related Processes 1
A Conducting a DOE in Minitab - Improving Surface Finish of an Impeller Using Minitab Software 10
N PCB (medical device) Surface Finish Selection. Manufacturing and Related Processes 2
S Surface Finish - Conversion factor to transform Rz Jis in Rz Inspection, Prints (Drawings), Testing, Sampling and Related Topics 6
N MSA (Measurement Systems Analysis) for Surface Finish Equipment Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
P Inner Diameter Surface Finish Ra Value vs. Surface Finish Graph Output Manufacturing and Related Processes 11
ScottK Inspecting surface finish on SS on a piece that can't be measured with current equip. Inspection, Prints (Drawings), Testing, Sampling and Related Topics 2
ScottK Surface Finish on machined brass (or other metals)- Attribute or Variable inspection? Inspection, Prints (Drawings), Testing, Sampling and Related Topics 8
ScottK Measuring Capability on a One Sided Variable (Surface Finish) Capability, Accuracy and Stability - Processes, Machines, etc. 17
W Surface Finish Measurement Technique Manufacturing and Related Processes 3
T Surface Finish Requirements (Ra 150) for Blasted Titanium Surfaces Manufacturing and Related Processes 12
J Surface Finish Tester Recommendations with both Ra and Rz (english and metric) scales Inspection, Prints (Drawings), Testing, Sampling and Related Topics 1
Ron Rompen Conversion of surface finish measurements Inspection, Prints (Drawings), Testing, Sampling and Related Topics 4
U How to do Gage R&Rs on Surface Finish Gages Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
Geoff Cotton Surface Finish - G5 - Where is this from and how can I measure it? Manufacturing and Related Processes 6
Marc Surface Finish Gage R&R Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
J The best way to define a surface finish General Measurement Device and Calibration Topics 1
J Surface Finish - What is the meaning of the term ?LAY?? Coffee Break and Water Cooler Discussions 4
D Air Gauging: Are the results affected by surface finish of the bore? General Measurement Device and Calibration Topics 1
P Surface scratch measurement General Measurement Device and Calibration Topics 1
D Surface Roughness understanding Inspection, Prints (Drawings), Testing, Sampling and Related Topics 1
D Calibration of Digital thermometer with surface probe General Measurement Device and Calibration Topics 1
R Design and Manufacture Guidelines for Surface Mount Technology Misc. Quality Assurance and Business Systems Related Topics 9
M Active Surface Disinfectant Claims - FDA vs EPA and Hands vs Objects Other Medical Device and Orthopedic Related Topics 0
P Gas Nitriding Surface Hardening of Stainless Steel 304 ISO 13485:2016 - Medical Device Quality Management Systems 4
N Creepage - Does a surface mount isolator body negate a PCB slot? IEC 60601 - Medical Electrical Equipment Safety Standards Series 6
CCaantley Where to get a good test indicator stand for a granite surface plate General Measurement Device and Calibration Topics 8
M Interesting Discussion Surface Cleanliness Real Time Test Tools General Measurement Device and Calibration Topics 2
P Romer Arm - Profile of a Surface Changing General Measurement Device and Calibration Topics 4
R Reporting Profile of a surface with U modifier Inspection, Prints (Drawings), Testing, Sampling and Related Topics 4
S Response Surface Method to create design matrix in Minitab Using Minitab Software 5
B Profile of a Surface Callout on this Drawing General Measurement Device and Calibration Topics 4
O Can a Profile of a Surface have a Diameter Symbol? Inspection, Prints (Drawings), Testing, Sampling and Related Topics 3
Q Surface Roughness - Conversion of RS on a Print to RZ General Measurement Device and Calibration Topics 3
S ARP 1820 Surface Contamination Testing Various Other Specifications, Standards, and related Requirements 1
N Projection welding of nuts on zinc coated surface Manufacturing and Related Processes 3

Similar threads

Top Bottom