Verification of a Test Apparatus by using known nonconforming part(s)

H

harishvagrawal

#1
1.CAN THE MISTAKE PROOFING BE BY-PASSED? IS THERE A RED PART TEST?
> FREQUENCY?

can i get a format sample reply on the above question.:)
 
Elsmar Forum Sponsor

Jim Wynne

Staff member
Admin
#2
Re: Verification of Error Proofing

1.CAN THE MISTAKE PROOFING BE BY-PASSED? IS THERE A RED PART TEST?
> FREQUENCY?

can i get a format sample reply on the above question.:)
Where did the question come from? Can mistake-proofing be bypassed under what circumstances? What's a "red part test"? What does ">FREQUENCY" mean? :confused:
 
H

harishvagrawal

#4
Re: Verification of Error Proofing

the question came from my QSA audit report.

they(coustomer) want us to make a defective part and put it in the fixture and check weather non confirming part can be made and define the frequency for the same .

so i needed a format sample?:)
 

Howard Atkins

Forum Administrator
Staff member
Admin
#5
Re: Verification of error proofing

This is a standard test which is usually done at setup and change of shift.
Just add the check to your normal setup sheet.
Red part past test Yes/NO
You should also have a green part to check that this works as well
 
B

Bill Ryan - 2007

#6
Re: Verification of Error Proofing

If Howard's assumption is correct - it is also known as a "rabbit test" and follows Howard's red and green samples being run through to verify the device is working properly.
 
H

harishvagrawal

#7
Re: Verification of Error Proofing

thanks i got the idea .

can there be a sample format for the red test?
:)
 

Marc

Hunkered Down for the Duration with a Mask on...
Staff member
Admin
#8
Re: Verification of Error Proofing

Not really. It depends upon the specific test apparatus. As Howard pointed out, this is a simple matter of having a known good part and a known defective part and running both through the test apparatus to ensure the test apparatus if functioning correctly. Quite common and in general a good idea.
 
Thread starter Similar threads Forum Replies Date
S Documenting Design Verification Test Results (ISO 9001) Design and Development of Products and Processes 1
W Seeking Guidance Verification Test Strategy for Class B Medical Devices IEC 62304 - Medical Device Software Life Cycle Processes 1
T ISO 17025 Method Verification - One sided “F” test or two sided “F” test ISO 17025 related Discussions 1
S What is the difference between Verification and Validation of Test Reports? AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 5
O Location of Verification Test Procedures 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 4
L How do I document the chemical attributes in the Mill Test Report (MTR) verification Inspection, Prints (Drawings), Testing, Sampling and Related Topics 1
B Is Ship Test considered Design Verification or Design Validation? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 2
S Checklist for RA and QA Review of DVT (design verification test) for Software Other US Medical Device Regulations 2
A AS9100 - Verification of Raw Material Supplier Test Reports AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 23
F Medical Device Cleaning Lifecycle test - Developing a Design Verification Spec Other Medical Device and Orthopedic Related Topics 2
J Verification Test for Hydrogen De-embrittlement? Reliability Analysis - Predictions, Testing and Standards 21
E XRF vs. Spark Test for RoHS Compliance Verification RoHS, REACH, ELV, IMDS and Restricted Substances 24
C Raw Materials verification - Melt Flow Test - Resins: Customer not Satisfied ISO 13485:2016 - Medical Device Quality Management Systems 4
J How & how often to perform verification of Test Software of Automatic Test Equipment? General Measurement Device and Calibration Topics 3
F 4.11.1 Test Software Verification ? QS-9000 - American Automotive Manufacturers Standard 1
Y SaMD Verification and Validation SOP and Plan IEC 62304 - Medical Device Software Life Cycle Processes 2
S How to perform verification of the Statistical Analysis Software? Qualification and Validation (including 21 CFR Part 11) 2
M Sample record for verification performed by importers before placing a device on the market EU Medical Device Regulations 0
N Example for design and development planning,input,output,review,verification,validation and transfer Misc. Quality Assurance and Business Systems Related Topics 4
S Calibration/Verification of customer fixtures IATF 16949 - Automotive Quality Systems Standard 6
Q Calibration verification records 7.1.5.2.1 IATF 16949 - Automotive Quality Systems Standard 2
B AS9100D 7.1.5.2 Calibration or Verification Method using outside cal lab AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 1
M ISO14971:2019 - Verification of implementation and effectiveness of risk control ISO 14971 - Medical Device Risk Management 3
C Stress / Challenge Conditions for Design Verification Testing to Reduce Sample Size 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 11
A Verification protocol example Design and Development of Products and Processes 2
Q Sampling method for Distributor verification activities EU Medical Device Regulations 1
D Design Verification Sample Size vs Repeats Statistical Analysis Tools, Techniques and SPC 9
S IEC 62304 - Software verification cost IEC 62304 - Medical Device Software Life Cycle Processes 3
T Laboratory Verification after validation ISO 17025 related Discussions 3
D ISO 13485 - 7.3.6 Design and development verification - Do most folks create a separate SOP? ISO 13485:2016 - Medical Device Quality Management Systems 6
T Calibration or Verification -> Cm and Cmk, etc. Definitions, Acronyms, Abbreviations and Interpretations Listed Alphabetically 3
K IEC 62304 compliance - Code reviews as part of verification strategy IEC 62304 - Medical Device Software Life Cycle Processes 5
C Documentation for items used for Design Verification 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 4
P Design verification driven by new equipment. How is this different than process validation? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 1
NDesouza Verification of Supplier RCCAs Nonconformance and Corrective Action 5
I IATF 2016 - 8.5.1.4 Verification after shutdown due to COVID19 Process Maps, Process Mapping and Turtle Diagrams 1
M IATF 16949 8.5.1.3 Verification of job set-ups - Do we need secondary check? IATF 16949 - Automotive Quality Systems Standard 7
G Supplier flowdown verification of tests and revisions Supplier Quality Assurance and other Supplier Issues 0
G Devices from IQ, OQ or PQ process to be used for verification, validation and summative? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 5
M Calibration or Verification? What terminology to use ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 1
Bev D Verification and Validation of Measurement Systems Misc. Quality Assurance and Business Systems Related Topics 0
A Our auditor told if we didn't have a patent we would have to do a validation or verification ISO 13485:2016 - Medical Device Quality Management Systems 6
N Design Verification & Process Validation - Statistical sample sizes Design and Development of Products and Processes 2
D Design Verification - Is testing required? Design and Development of Products and Processes 5
J Verification of purchased product / Alexa as a medical device ISO 13485:2016 - Medical Device Quality Management Systems 6
C Machine Verification Plan Manufacturing and Related Processes 2
A What to do when 100 % verification is not 100 % Manufacturing and Related Processes 5
R Design Verification Documentation ISO 13485:2016 - Medical Device Quality Management Systems 19
D 510K and Changes to Verification and Validation US Food and Drug Administration (FDA) 2
R Design verification for interim design outputs - sampling rationale ISO 13485:2016 - Medical Device Quality Management Systems 2

Similar threads

Top Bottom