What are the Acceptance Criteria for Linearity Study?

B

Bharder

#1
#1
Targets for Linearity

I am looking for some recommendations for acceptance criteria for QS-9000 linearity studies. The MSA manual does not define acceptance criteria it just says that regression line should have a good linear fit(R squared) and good linearity or low slope. The auditor says I must have values or targets stated for these characteristics. I can't find any guidelines. Any ideas?
 
Highly Rated Gage Tracking - Learn More
Elsmar Forum Sponsor
Marc

Marc

Fully vaccinated are you?
Leader
#2
#2
As I understand it, you take the value of the instrument's range deviation and look at it as a % of the spec range. Was this brought up with respect to your uncertainty budget?
 
E

e.s.deo

#3
#3
Dear Bharder,

You hv to consider linearity as a proportion of the total r&r
As well as total tolerance.
We should not consider this in isolation!
If further details are provided we can better discuss this!

Thanks
e.s.deo
 
You must log in or register to reply here.
Thread starter Similar threads Forum Replies Date
B Can any one help me in Linearity calculations & acceptance criteria Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
R Acceptance Criteria for Linearity and Bias Studies - Engine Valves Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 1
N Acceptance Criteria for Linearity Test Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 3
D Gage R&R - Acceptance Criteria for Linearity, Bias, and Stability Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
F Tolerance Acceptance Criteria General Measurement Device and Calibration Topics 3
S How to determine sample size to test when the acceptance criteria is x >= Standard value? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 7
C Design output vs acceptance criteria ISO 13485:2016 - Medical Device Quality Management Systems 8
D IVD Accuracy and Precision Acceptance Criteria ISO 13485:2016 - Medical Device Quality Management Systems 1
H Medical Device Label Acceptance Criteria Manufacturing and Related Processes 10
D What are the acceptance criteria/requirements for Stability Study? General Measurement Device and Calibration Topics 7
L Gage R&R TMV Acceptance Criteria Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 4
M V&V phase: Justification of acceptance criteria (statistical method ) - (Medical Device) Design and Development of Products and Processes 2
O GR&R Acceptance Criteria Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
S Shore A hardness Tester Acceptance Criteria Standard Elsmar Cove Forum Suggestions, Complaints, Problems and Bug Reports 2
lanley liao Purchase Acceptance Criteria - Tensile testing Oil and Gas Industry Standards and Regulations 2
R Procedure, Frequency and Acceptance Criteria for Replicate, Recalibration, Before-After and Intermediate Checks ISO 17025 related Discussions 8
S Acceptance criteria for gauges General Measurement Device and Calibration Topics 9
M Characterization Testing - NO acceptance criteria, no minimum performance requirement Inspection, Prints (Drawings), Testing, Sampling and Related Topics 1
J AIAG PPAP: 2.2.11.3 Acceptance Criteria for Initial Study (page 9, 4th edition) APQP and PPAP 1
C FDA on changing acceptance criteria re: analytical method validation US Food and Drug Administration (FDA) 1
B IATF 16949 Cl. 8.6.6 - Acceptance Criteria - Zero Defects Attribute Data Sampling IATF 16949 - Automotive Quality Systems Standard 2
P Medical Device Validation Protocols and Reports - Acceptance Criteria Other Medical Device and Orthopedic Related Topics 3
C Software Unit Acceptance Criteria (5.5.4) IEC 62304 - Medical Device Software Life Cycle Processes 3
J Acceptance Criteria in 8.1.1 e) of IATF 16949 IATF 16949 - Automotive Quality Systems Standard 2
O Acceptance criteria bacterial endotoxins immunosera for human use Manufacturing and Related Processes 3
I As a part of validation, should i include the acceptance criteria of CPk index >1.33? Qualification and Validation (including 21 CFR Part 11) 4
V Acceptance Criteria Gage R&R - Simple vs Complex Techniques Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 8
A 5.5.3 - Software Unit Acceptance Criteria (Risk Control Measures) IEC 62304 - Medical Device Software Life Cycle Processes 3
M Establishment of Acceptance Criteria for a Weigh Balance General Measurement Device and Calibration Topics 3
X How to define Calibration Acceptance Criteria General Measurement Device and Calibration Topics 3
P Gage R (no reproducibility) - Acceptance Criteria Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 2
V Validation Test and Acceptance Criteria for Compressed Air Qualification and Validation (including 21 CFR Part 11) 3
I Dual Acceptance Criteria: Cpk and Individual Values Statistical Analysis Tools, Techniques and SPC 3
L Acceptance Criteria for External Calibrated Standards IATF 16949 - Automotive Quality Systems Standard 1
A Risk Acceptance Criteria in ISO 14971 ISO 14971 - Medical Device Risk Management 19
G Acceptance Criteria when Verifying a Gauge General Measurement Device and Calibration Topics 2
D Renault Painting Defect Acceptance Criteria Manufacturing and Related Processes 4
B Surface Roughness Tester Acceptance Criteria Calibration Frequency (Interval) 4
H Package Integrity Testing Acceptance Criteria ISO 13485:2016 - Medical Device Quality Management Systems 3
D 21 CFR 820.80 In-Process Acceptance Criteria requirements for IVDs 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 3
S Acceptance Criteria for Scratches on Medical Devices ISO 13485:2016 - Medical Device Quality Management Systems 3
JoCam Nadcap AC7120 (Audit Criteria for Circuit Card Assemblies) - Acceptance Criteria AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 3
A Acceptance Criteria - ISO 9001:2008 Clause 8.2.4 - Questionable Audit Finding? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 40
Q How to meet Clause 7.1.2 Acceptance Criteria in ISO TS 16949 IATF 16949 - Automotive Quality Systems Standard 7
J IPC-A-610 E Thermal Plane Acceptance Criteria for D-Pak Component Other ISO and International Standards and European Regulations 2
S Acceptance Criteria at Design Verification Inspection, Prints (Drawings), Testing, Sampling and Related Topics 2
P Labels - ASTM D3330/D3330M Acceptance Criteria for Adhesion 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 1
optomist1 Tensile Test Crimped Electrical Terminal Acceptance Criteria Inspection, Prints (Drawings), Testing, Sampling and Related Topics 3
V The approach/criteria of setting Acceptance Limits Method Validation Parameters Statistical Analysis Tools, Techniques and SPC 1
6 Acceptance Criteria For pH Meters and other Laboratory Equipment Measurement Uncertainty (MU) 16

Similar threads

Top Bottom