Where to place our Safety Program in our QMS?

Q

Quality_Goblin

Involved In Discussions
We are implementing a safety program and we want to have all the documents and written procedures controlled and part of the QMS. My question is - what section of the standard should we place our Safety Program documents? Initially I was thinking 7.2 Qualification and Awareness. Or should it be in 7.1.3 Maintenance and Infrastructure?
 
bryan willemot

bryan willemot

Involved In Discussions
Hello, you can pick the following areas:
  • Management Commitment – Executives should be committed to guaranteeing the production of quality and safe products and services.
  • Continuous Improvement – Organisations should regularly assess the effectiveness of the Quality Management System and their health and safety hazard controls.
  • Communication – There should be a unified program to communicate policies and objectives across all organization levels.
or you can seek out In clause 6.4 of ISO 9001, organisations must identify and manage the work environment required to produce quality products and services. Physical factors such as hygiene, noise, and human factors such as employee supervision are some of the areas to be considered.

hope this helps
 
Randy

Randy

Super Moderator
bryan willemot said:
In clause 6.4 of ISO 9001, organisations must identify and manage the work environment required to produce quality products and services. Physical factors such as hygiene, noise, and human factors such as employee supervision are some of the areas to be considered.

hope this helps
Click to expand...

If you're going to help please use a correct reference.....There is no 6.4 in ISO 9001, so no it doesn't help
 
Randy

Randy

Super Moderator
Quality_Goblin said:
My question is - what section of the standard should we place our Safety Program documents? Initially I was thinking 7.2 Qualification and Awareness. Or should it be in 7.1.3 Maintenance and Infrastructure?
Click to expand...

No don't do any of it...........Documents would need to be controlled and that's under 7.5.

But why are you putting it into your Quality Program? If anything it would be complimentary to 7.1.4 Environment for the operation of processes..........BUT NOOOOOOOOOOOO! Just look at the attached to help you out..........However if you are in South Carolina you'd better have a Safety Program in place yesterday meeting 29CFR 1910 General Industry
 

Attachments

  • 1 Correspondence table 45-14-9.docx
    23.4 KB · Views: 64
Q

Quality_Goblin

Involved In Discussions
I am just going off what my CQO wants. And we have two facilities - one in California, one in North Carolina. :)

Randy said:
No don't do any of it...........Documents would need to be controlled and that's under 7.5.

But why are you putting it into your Quality Program? If anything it would be complimentary to 7.1.4 Environment for the operation of processes..........BUT NOOOOOOOOOOOO! Just look at the attached to help you out..........However if you are in South Carolina you'd better have a Safety Program in place yesterday meeting 29CFR 1910 General Industry
Click to expand...
 
ChrisM

ChrisM

Quite Involved in Discussions
^
In the document that Randy has attached, there are one too many zeros in the first column... 45001 not 450001, but this is a great aid; thanks Randy
 
bryan willemot

bryan willemot

Involved In Discussions
Randy said:
If you're going to help please use a correct reference.....There is no 6.4 in ISO 9001, so no it doesn't help
Click to expand...
My bad I was looking in my quality manual. I guess its ok when the "super Moderator" puts an extra 0 in his statement... so forget my 6.4 reference.
 
Randy

Randy

Super Moderator
bryan willemot said:
My bad I was looking in my quality manual. I guess its ok when the "super Moderator" puts an extra 0 in his statement... so forget my 6.4 reference.
Click to expand...
Oops, understandable now...At least it seems your manual isn't the usual boring cut & paste
 
You must log in or register to reply here.
Thread starter Similar threads Forum Replies Date
shimonv Where do you place Human Factors report in a 510(k) application? Other US Medical Device Regulations 3
M Testing criteria - where to place Design and Development of Products and Processes 2
L Where to place the what/when/how/who/where procedures in a multi-regulation AS9110C organisation AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 3
C Where to place CE/label in Sterile IVD EU Medical Device Regulations 1
J Where to Place Process Maps in our Documentation? Process Maps, Process Mapping and Turtle Diagrams 4
A What if Contract Manufacturers does not have an ISO 13485 certificate? Where will the NB audit take place, at legal mfg. site or contract mfg. site? Other Medical Device Regulations World-Wide 3
Q Where to place a Down Stream Gage Inspection on an FMEA FMEA and Control Plans 5
S Where is a good place to get IMDS (International Material Data System) Training? IATF 16949 - Automotive Quality Systems Standard 3
N Putting SOPs in place in preparation for ISO certification - where to start? Service Industry Specific Topics 5
ScottK Where's your favorite place for Lunch? Coffee Break and Water Cooler Discussions 36
T Definition Gemba is a japanese term for place (Where the action is) Definitions, Acronyms, Abbreviations and Interpretations Listed Alphabetically 12
A Is there a place where I can purchase ISO 9001:2000 posters? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 7
T Where to Place Process Maps in our Documentation Process Maps, Process Mapping and Turtle Diagrams 20
R ISO Publications - Where the best place to purchase ISO 9001 publications? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 2
E Class II symbol - where to apply it? IEC 60601 - Medical Electrical Equipment Safety Standards Series 2
T Good Documentation Practices (GDocP) - Where are these described in the regulations? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 7
A Where 60601-1 represented in the 510k submission? US Medical Device Regulations 6
Q Where did my Alignment go wrong? MCOSMOS Inspection, Prints (Drawings), Testing, Sampling and Related Topics 2
MaHoDie Where to show the Software version IEC 62304 - Medical Device Software Life Cycle Processes 2
E Where can i get latest toyota and honda Supplier Quality Assurance Manual (SQAM) Customer and Company Specific Requirements 3
I Where to find MDR compliance device? EU Medical Device Regulations 6
N Writing Risk Management procedure for small manufacturing and we don't know where to start. Manufacturing and Related Processes 9
I ISO 9000 Where to Start ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 93
Ajit Basrur Where to find a pagination requirement as "Page x of y"? ISO 13485:2016 - Medical Device Quality Management Systems 7
T Assessing risk where harm is indirect - Generic devices / accessories / intermediates ISO 14971 - Medical Device Risk Management 8
J Incoming Stock QC, where to start? Manufacturing and Related Processes 6
J Stock Traceability Methods, where to start? Manufacturing and Related Processes 0
B Where do the definitions of the types of processes come from? IATF 16949 - Automotive Quality Systems Standard 9
Awais Where to get started on DFM / DFMA Manufacturing and Related Processes 2
S Where to start for MDSAP for Canada? Canada Medical Device Regulations 5
D Deviations - Where in ISO 13485 deviations are covered? ISO 13485:2016 - Medical Device Quality Management Systems 7
D Question regarding where "validations" fit according to ISO 13485:2016 ISO 13485:2016 - Medical Device Quality Management Systems 1
A MDR requirement where unit of use packaging is too small for UDI carrier EU Medical Device Regulations 1
J UDI - Where to document it? EU Medical Device Regulations 8
J Where to get a Black belt certification ASQ, ANAB, UKAS, IAF, IRCA, Exemplar Global and Related Organizations 13
D Any recommendations on where to find experienced quality hires in Chicago area? Job Openings, Consulting and Employment Opportunities 2
J Where is the definition of a critical supplier? ISO 13485:2016 - Medical Device Quality Management Systems 5
W Where does a coatings and paint company fall in IATF? IATF 16949 - Automotive Quality Systems Standard 5
B When Travel is allowed - Where are you going? Travel - Hotels, Motels, Planes and Trains 24
G Where to buy Template / sample SCSMS Manual, checklist Supply Chain Security Management Systems 1
S Where do l get calibration standards to run a calibration lab? Other ISO and International Standards and European Regulations 2
M Quality Manual - Where does Revision History Section go? Document Control Systems, Procedures, Forms and Templates 8
C Where to draw the line for "sufficient evidence" to verify safety/performance of a device? CE Marking (Conformité Européene) / CB Scheme 2
B Where to acquire EN 868-5 required dye (Amaranth red)? Other Medical Device Related Standards 2
N Where to find Regulations for Reprocessing and Reuse of Single-Use Devices Other Medical Device Related Standards 2
H Where to get EK MED 1927/16 Other Medical Device Regulations World-Wide 3
D Where to find Guidance Class II Amendment Canada Medical Device Regulations 1
O EN 301 489-1 and EN 301 489-17 - Where do we get the information of the Published versions? CE Marking (Conformité Européene) / CB Scheme 1
A AS9100 Training - Where do I start? AS9100, IAQG, NADCAP and Aerospace related Standards and Requirements 14
qualprod Records where apply and stop recording everything? ISO 9000, ISO 9001, and ISO 9004 Quality Management Systems Standards 4

Similar threads

Top Bottom