Leak Detection - Oven Seals

W

Welty

#1
#1
I am looking for a devise that is able to detect leaks in oven seals. These ovens will need to be tested at full temp - 700 degrees. Testing will need to show results of leaks in the oven door, current testing methods are the use of smoke. I am looking for an environmental / safety freindly product. Open to any suggestions.

Thanks in advance!!!

LW

:bigwave:
 
Download Free White Paper
Elsmar Forum Sponsor
Jerry Eldred

Jerry Eldred

Forum Moderator
Super Moderator
#2
#2
Depending on what exactly you are looking for, you could possible use an Infrared thermometer. There are a number of manufacturers/Distributors I am familiar with on these:

Omega Engineering (doesn't make, but sells quite a few)
Raytek
Fluke I believe sells one that can be used as an accessory to a handheld mutimeter.

These can be used to find "HOT SPOTS" (i.e.: leaks in the door).
 
You must log in or register to reply here.
Thread starter Similar threads Forum Replies Date
L Environmental Gas Leak Detection Equipment Recomendations Miscellaneous Environmental Standards and EMS Related Discussions 2
ScottK Oxygen Cleaning and Surfactants used for leak detection Various Other Specifications, Standards, and related Requirements 1
S Capability Study for Leak Tester Capability, Accuracy and Stability - Processes, Machines, etc. 9
S Capability or Gage R&R Study for Leak Tester? Reliability Analysis - Predictions, Testing and Standards 15
N MSA Study for a Leak Testing Device Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 9
M Proper ISO standard for Pressure Testing and Leak Rates Inspection, Prints (Drawings), Testing, Sampling and Related Topics 6
H Validating Nondestructive leak testing machine Qualification and Validation (including 21 CFR Part 11) 3
F Leak Tester Gage R&R Sheet Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 0
triathlonx13 Leak test correlation - Bubble to Air Reliability Analysis - Predictions, Testing and Standards 8
O Capability or Gage R&R Study for Leak Tester Reliability Analysis - Predictions, Testing and Standards 11
GURU SDI Leak Testing - O-ring installation in the groove of Bore ID Problem Solving, Root Cause Fault and Failure Analysis 4
T Would a Leak be a Failure Mode on a Design FMEA? Design and Development of Products and Processes 2
GURU SDI Measurement - Pressure Drop vs. Leak Rate Inspection, Prints (Drawings), Testing, Sampling and Related Topics 8
S Destructive Attribute MSA for Simple Water Leak Check in Trailers Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 5
somashekar Why does a tap leak... Funny Stuff - Jokes and Humour 2
B Validation of a Pressure Decay Leak Tester for a Medical Device Design and Development of Products and Processes 2
Claes Gefvenberg Massive gas leak off Scotland World News 12
H Determining Calibration Tolerance for new Leak and Occlusion Equipment Measurement Uncertainty (MU) 2
N Tyvek Pouch Seal - Pressure needed to conduct Vacuum Seal Leak test? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 2
V For an MDI, is leak-test a stability parameter ? 21 CFR Part 820 - US FDA Quality System Regulations (QSR) 2
S Zyglo Fluorescent Dye for Leak Testing - Sloooooow acting - Seeking advice Reliability Analysis - Predictions, Testing and Standards 4
R Sample Size for P Chart - 100% Leak Test for Condensor Inspection, Prints (Drawings), Testing, Sampling and Related Topics 5
R Seal Packaging - Burst and Leak Specifications for a Foil Seal applied to a PTFE well Manufacturing and Related Processes 4
T Gage Repeatability for an Automated Leak Tester Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 10
W Oven Leak Test Method - Integrity of the chamber to hold gas Qualification and Validation (including 21 CFR Part 11) 3
D Leak Test Method for Balloon Catheters EU Medical Device Regulations 2
B MSA (Gage R&R) vs. Capability Cpk Study - Helium Leak Check Station Statistical Analysis Tools, Techniques and SPC 2
D Halogen Leak Detector - Calibration source needed General Measurement Device and Calibration Topics 1
G Leak Tester Calibration - Sentinal C-20 controller with a calibrated orifice General Measurement Device and Calibration Topics 1
G Leak Test - Building a master pump to calibrate pump tester Inspection, Prints (Drawings), Testing, Sampling and Related Topics 4
T Calibration of vacuum type leak detectors manufactured by Vacuum Technology Inc General Measurement Device and Calibration Topics 5
H GR&R (Gage R&R) on leak test equipment is there a deviation requirment? Gage R&R (GR&R) and MSA (Measurement Systems Analysis) 5
R Calibrating Leak Testers - Old fashioned water tank type tester General Measurement Device and Calibration Topics 2
C Master Validation Frequency in production - Absence of leak, thread presence, etc. Reliability Analysis - Predictions, Testing and Standards 4
M Developing a Leak Test - Housing part for an automotive customer Various Other Specifications, Standards, and related Requirements 7
A PFMEA detection for "none" FMEA and Control Plans 5
J Is it correct to have a detection (error proofing) in subsequent operation? FMEA and Control Plans 10
M Detection rank for sampling vs 100% inspection & 15x vs 400x magnification FMEA and Control Plans 4
T RPN Thresholds and How Detection Fits In ISO 14971 - Medical Device Risk Management 5
B Handling lower detection limits for SPC and process performance Statistical Analysis Tools, Techniques and SPC 1
T Annual Validation as a detection mode on a PFMEA? FMEA and Control Plans 5
P Design FMEA - Detection Rating criteria ISO 14971 - Medical Device Risk Management 3
I Does anybody use Detection in medical device Design FMEA? ISO 14971 - Medical Device Risk Management 25
A Literature review/HACCP validation of metal detection Food Safety - ISO 22000, HACCP (21 CFR 120) 0
Jimmy123 FMEA - Preventive vs Detection Control FMEA and Control Plans 7
B Detection of Orange peel Manufacturing and Related Processes 3
C Detection Action for Failure Effects - AIAG 4th Edition Layout FMEA and Control Plans 5
C PCBA Hardware Component different failure types - How to rate detection? FMEA and Control Plans 8
P Detection rating for a user (surgeon) related failure mode in DFMEA APQP and PPAP 3
S Are Defibrillator Protection and Pacemaker pulse detection features mandatory as per IEC 60601-2-25 or 2-27...? IEC 60601 - Medical Electrical Equipment Safety Standards Series 11

Similar threads

Top Bottom